Product Catalogue

Converter to connect an IDC20A Debug Cable to a standard 6-pin "Pmod™" connector “Pmod™” is a trademark of Digilent Inc Former name: Conv. ARM-20 to Digilent PMOD

State-Timing Analyzer to record digital or analog signal via suitable probes. Records up to 102 (51) channels, 200 (400) MHz state, 250 (500) MHz timing, transient recording, 64 MFrames, 48-bit time-stamp, trigger, filter, trigger Delay, etc. This is an extension that attaches to an existing PowerDebug X50, PowerDebug PRO, or PowerDebug II. Available probes: LA-7945 Standard Probe (17 digital single-ended signals) LA-7944 Mictor Probe (34 digital single-ended signals) LA-7946 Samtec Probe (34 digital single-ended signals) LA-7947 Mictor Differential Probe (17 digital differential signals) LA-7954 Mictor Probe with differential clock (32 se + 1 diff signal) LA-7958 Samtec Probe with differential clock (32 se + 1 diff signal) LA-7961 USB2 Probe LA-7943 DigRF Probe Set LA-7949 Analog Probe

State-Timing Analyzer to record digital or analog signal via suitable probes. Records up to 102 (51) channels, 200 (400) MHz state, 250 (500) MHz timing, transient recording, 128 MFrames, 48-bit time-stamp, trigger, filter, trigger Delay, etc. This is an extension that attaches to an existing PowerDebug X50, PowerDebug PRO, or PowerDebug II. Available probes: LA-7945 Standard Probe (17 digital single-ended signals) LA-7944 Mictor Probe (34 digital single-ended signals) LA-7946 Samtec Probe (34 digital single-ended signals) LA-7947 Mictor Differential Probe (17 digital differential signals) LA-7954 Mictor Probe with differential clock (32 se + 1 diff signal) LA-7958 Samtec Probe with differential clock (32 se + 1 diff signal) LA-7961 USB2 Probe LA-7943 DigRF Probe Set LA-7949 Analog Probe

State-Timing Analyzer to record digital or analog signal via suitable probes. Records up to 102 (51) channels, 200 (400) MHz state, 250 (500) MHz timing, transient recording, 256 MFrames, 48-bit time-stamp, trigger, filter, trigger Delay, etc. This is an extension that attaches to an existing PowerDebug X50, PowerDebug PRO, or PowerDebug II. Available probes: LA-7945 Standard Probe (17 digital single-ended signals) LA-7944 Mictor Probe (34 digital single-ended signals) LA-7946 Samtec Probe (34 digital single-ended signals) LA-7947 Mictor Differential Probe (17 digital differential signals) LA-7954 Mictor Probe with differential clock (32 se + 1 diff signal) LA-7958 Samtec Probe with differential clock (32 se + 1 diff signal) LA-7961 USB2 Probe LA-7943 DigRF Probe Set LA-7949 Analog Probe

State-Timing Analyzer to record digital or analog signal via suitable probes. Records up to 204 (102) Channels, 200 (400) MHz State, 250 (500) MHz Timing, Transient Recording, 8 MB sample memory, 512 KFrames, 48 Bit Time-Stamp, Trigger Filter, Trigger Delay, etc. This is an extension that attaches to an existing PowerDebug module. Available probes: LA-7945 Standard Probe (17 digital single-ended signals) LA-7944 Mictor Probe (34 digital single-ended signals) LA-7946 Samtec Probe (34 digital single-ended signals) LA-7947 Mictor Differential Probe (17 digital differential signals) LA-7954 Mictor Probe with differential clock (32 se + 1 diff signals) LA-7958 Samtec Probe with differential clock (32 se + 1 diff signals) LA-7961 USB2 Probe LA-7943 DigRF Probe Set LA-7949 Analog Probe

Converter to connect an ARM Preprocessor and a CombiProbe to a Mictor connector on the target. This converter is designed for the OMAP3503 board from Spectrum Digital. The upper ETM signals on the Mictor can alternatively be used for system trace (SDTI).

Package of PowerTrace-III Universal Trace Port Controller, and Mixed-Signal Probe Digital/Analog 40-pin connector Characteristics of digital probe 12 channels (12 data) 0..5 V Input 200 MSamples per channel Characteristics of analog probe 6 Channels -12V..+12V 13 bit resolution, 2 current sense channels, Conversion rate 1 MSample/s requires PowerDebug II Ethernet or PowerDebug PRO and TRACE32 software DVD 2021/02 or newer Recommended accessories: LA-6470 Clip Set (Cable and Clips)

Probe to record digital signals from a Mictor connector: 34 Channels (32 Data, 2 Clock), 0..5 V Input, 4 pF, 50 kOhm. The probe requires one of the following modules. PowerIntegrator (LA-7940), PowerIntegrator II (LA-3940/3941/3942).

Probe to record digital signals from a Samtec connector: 34 Channels (32 Data, 2 Clock), 0..5 V Input, 4 pF, 50 kOhm. The probe requires one of the following modules. PowerIntegrator (LA-7940), PowerIntegrator II (LA-3940/3941/3942).

Probe to record digital signals from a Mictor connector with differential clock signal: 33 Channels (32 Data, 1 pair of differential clock), 0..5 V Input, 4 pF, 50 kOhm. The probe requires one of the following modules. PowerIntegrator (LA-7940), PowerIntegrator II (LA-3940/3941/3942).

Probe to record digital signals from a Samtec connector with differential clock signal: 33 Channels (32 Data, 1 pair of differential clock), 0..5 V Input, 4 pF, 50 kOhm. The probe requires one of the following modules. PowerIntegrator (LA-7940), PowerIntegrator II (LA-3940/3941/3942).

Digital/Analog probe with 40-pin connector for LA-3204 MicroTrace for Cortex-M (PACK) LA-3080 CombiProbe 2 for MIPI20T-HS (PACK) LA-3081 CombiProbe 2 for AUTO26 (PACK) LA-3082 CombiProbe 2 for MIPS32+4-Bit IFLOW (PACK) LA-3083 CombiProbe 2 for MIPI34 (PACK) LA-2520 / LA-2521 PowerTrace III LA-3121 / LA-3122 PowerTrace Serial 2 Characteristics of digital probe: 12 channels (12 data), 0..5 V Input, 200 MSamples per channel. Characteristics of analog probe: 6 Channels -12V..+12V 13 bit resolution, 2 current sense channels, Conversion rate 1 MSample/s. Requires TRACE32 software DVD 2021/02 or newer. Recommended accessories: LA-6470 Clip Set (Cable and Clips)

Probe to record differential digital signals from a Mictor connector: 17 Difference Channels (16 Data, 1 Clock), 0..5 V Input, 4 pF, 50 kOhm. The probe requires one of the following modules. PowerIntegrator (LA-7940), PowerIntegrator II (LA-3940/3941/3942), PowerTrace II (LA-7692/7693/7694), PowerTrace Serial (LA-3120/3520/3555/3560).

Converter from IDC20A to 12 pin PMOD connectors with the JTAG pinout from SiFive. The adapter exists in two variants: with male and female PMOD connector. This adapter has the male PMOD connector. PMOD is an open standard defined by Digilent for peripherals used with FPGAs or microcontrollers. The PMOD pinout of this adapter does ONLY work with targets that use the pinout that was defined by SiFive. So it is not a general/official RISC-V pinout. In case of FPGA boards, the pinout may depend on the used FPGA image.

Converter from IDC20A to 12 pin PMOD connectors with the JTAG pinout from SiFive. The adapter exists in two variants: with male and female PMOD connector. This adapter has the female PMOD connector. PMOD is an open standard defined by Digilent for peripherals used with FPGAs or microcontrollers. The PMOD pinout of this adapter does ONLY work with targets that use the pinout that was defined by SiFive. So it is not a general/official RISC-V pinout. In case of FPGA boards, the pinout may depend on the used FPGA image.

All-In-One Debug and Trace Solution for Arm Cortex-M. Supports 5-pin standard JTAG, cJTAG and Serial Wire Debug Port for Arm Cortex-M cores and SecurCore SC000/SC300 Includes 256-MByte of trace RAM to support: - ITM via Serial Wire Output/TPIU - ETM Cortex-M continuous mode via TPIU (4-bit) Bandwidth of 400 MBit/s per trace channel. Trace Streaming up to 100 MByte/s requires USB 3.0 (SuperSpeed) capable host computer Concurrent debugging of two or more Cortex-M cores requires a License for Multicore Debugging MicroTrace (LA-7960N) Can not be upgraded to include support for other core architectures. Extend your MicroTrace with a Mixed-Signal Probe (LA-2500), to record and correlated digital and analog signals.

Probe to record digital signals from a 20 pin IDC connector: 17 Channels (16 Data, 1 Clock), 0..5 V Input, 4 pF, 50 KOhm. The probe requires one of the following modules. PowerIntegrator (LA-7940), PowerIntegrator II (LA-3940/3941/3942), PowerTrace II (LA-7692/7693/7694), PowerTrace Serial (LA-3120/3520/3555/3560). The probe is not suitable for PowerTrace III (LA-2520/2521), PowerTrace II Lite (LA-3580/3581), PowerTrace Serial 2 (LA-3121/3122), CombiProbe 2 (LA-3060) and MicroTrace (LA-3050). For those devices, you can use the Mixed-Signal Probe (LA-2500) instead (except for PowerTrace II Lite). Includes a 20 pin male-male adaptor.

CombiProbe 2 to debug and trace MIPS32 CPUs with 4 Bit IFLOW trace. Voltage Range: 1.2V...3.3V (5V tolerant inputs). Target Connector: MIPI34, MIPI20T, MIPI10, eJTAG/IFLOW. Trace memory: 512 MByte. Maximum trace port width: 4 pins. Maximum trace bandwidth: 200 MBit/s per trace pin. Iincluded adapter for eJTAG and IFLOW connector. Includes the TRACE32 software for Windows, Linux and macOS on DVD and for download. Requires the following A-license: LA-7760A (JTAG Debugger for MIPS32). 4-Bit IFlow program trace requires: LA-7971X (Trace License for the MIPS32). Requires TRACE32 Software R.2022.02 (build 142224) or newer. Requires Power Debug Interface USB 3.0, PowerDebug II, PowerDebug PRO, PowerDebug E40 or PowerDebug X50. Extend your CombiProbe with a Mixed-Signal Probe (LA-2500), to record and correlate digital and analog signals.

CombiProbe 2 with MIPI34 whisker for debugging and tracing. Voltage Range: 1.2V...3.3V (5V tolerant inputs). Target Connector: MIPI34, MIPI20T, MIPI10 Trace memory: 512 MByte. Maximum trace port width: 4 pins. Maximum trace bandwidth: 200 MBit/s per trace pin. Includes the TRACE32 software for Windows, Linux and macOS on DVD and for download. Requires at least one of the following A-licenses: LA-3743A Debug. for Cortex-A/R (Armv8 and Armv9) Add. LA-7844A Debug Cortex-M (Armv6/7/8 32-bit) Add. LA-7843A Debug Cortex-A/-R (Armv7 32-bit) Add. LA-7765A JTAG Debugger License for Arm11 Add. LA-7742A JTAG Debugger License for Arm9 Add. LA-7746A JTAG Debugger License for Arm7 Add. Requires trace license LA-7970X for on-chip ETM traces of Cortex-A/R. Requires Power Debug Interface USB 3.0, PowerDebug II, PowerDebug PRO, PowerDebug E40 or PowerDebug X50. Extend your CombiProbe with a Mixed-Signal Probe (LA-2500), to record and correlate digital and analog signals.

CombiProbe 2 with AUTO26 Whisker for debugging and DAP Streaming, supporting DAP (DAP2, DAP3, DAP4, DAPWide), JTAG, DXCPL/DXCM. For optimal performance, we recommend using a DAP mode. DAP streaming is supported for TriCore (in DAP mode) and works most effectively with DAPWide (up to 320 Mbit/s). For DXCPL/DXCM, you will likely require the CAN-Box (LA-3889) as well. Voltage Range: 1.8V to 5.0V. Debug Clock Frequency: 10 kHz to 160 MHz Target Connector: AUTO26, AUTO20, AUTO10 Trace Memory: 512 MByte. Includes the TRACE32 software for Windows, Linux and macOS on DVD and for download. Requires the following A-license: LA-7756A (Debugger for TriCore Standard Additional). Trace analysis and display requires LA-3799X (Trace License for TriCore ED). Requires Power Debug Interface USB 3.0,PowerDebug II, PowerDebug PRO, PowerDebug E40 or PowerDebug X50. Please note that TriCore SoCs usually support only 3.3V or 5V in DAP mode. Debug clock frequency in JTAG mode is typically limited to 40 MHz on TriCore SoCs (while up to 160 MHz is supported in DAP mode). Extend your CombiProbe with a Mixed-Signal Probe (LA-2500), to record digital and analog signals and correlate them with MCDS DAP streaming. (Requires PowerView R.2024.02 or higher).