Search results for "idt"
Supports Armv8 and Armv9 based Cortex-A, Cortex-R, Cortex-X and Neoverse 32/64-bit cores GTM, SPT, IPU and Multicore debugging included IDC20A debug cable supports 5-pin standard JTAG, cJTAG and Serial Wire Debug Port, (0.4V - 5V) Includes software for Windows, Linux and macOS cJTAG and SWD require PowerDebug Interface USB 2.0/USB 3.0, PowerDebug Ethernet, PowerTrace, PowerDebug II PowerDebug PRO, PowerDebug E40 or PowerDebug X50
Converter from IDC20A and HSSTP to R-Car H3 Starter Kit from Renesas Former name: Conv. ARM-20/Samtec40 HSSTP to RCAR-H3-SKIT
Converter from IDC20A to 12 pin PMOD connectors with the JTAG pinout from SiFive. The adapter exists in two variants: with male and female PMOD connector. This adapter has the male PMOD connector. PMOD is an open standard defined by Digilent for peripherals used with FPGAs or microcontrollers. The PMOD pinout of this adapter does ONLY work with targets that use the pinout that was defined by SiFive. So it is not a general/official RISC-V pinout. In case of FPGA boards, the pinout may depend on the used FPGA image.
Converter from IDC20A to 12 pin PMOD connectors with the JTAG pinout from SiFive. The adapter exists in two variants: with male and female PMOD connector. This adapter has the female PMOD connector. PMOD is an open standard defined by Digilent for peripherals used with FPGAs or microcontrollers. The PMOD pinout of this adapter does ONLY work with targets that use the pinout that was defined by SiFive. So it is not a general/official RISC-V pinout. In case of FPGA boards, the pinout may depend on the used FPGA image.
Supports Armv7-A/R based Cortex-A and Cortex-R 32-bit cores GTM and IPU debugging included IDC20A debug cable supports 5-pin standard JTAG, cJTAG and Serial Wire Debug Port, (0.4V - 5V) Includes software for Windows, Linux and macOS cJTAG and SWD require PowerDebug Interface USB 2.0/USB 3.0, PowerDebug Ethernet, PowerTrace, PowerDebug II PowerDebug PRO, PowerDebug E40 or PowerDebug X50
Converter to connect the ARM Debug Cable or the CombiProbe to a Mictor connector on the target. This is needed if you want to debug without a Preprocessor and if there is only a Mictor connector on the target. The trace signals of the CombiProbe are connected to the lowest four trace signals of the Mictor (ETMv3 pinout, continuous mode). But tracing is normally no use case due to the bandwidth limitations of the CombiProbe. Former name: ARM Conv. ARM-20/MIPI-34 to Mictor-38
Supports 78K0R and RL78 cores (16-bit). Uses IDC20A debug cable, which supports 5-pin standard JTAG, cJTAG (IEEE 1149.7) and Serial Wire Debug (SWD), (0.4V - 5V) Includes software for Windows, Linux and macOS. Requires PowerDebug base module. Not supported are the very old 1st Gen. PowerDebug modules LA-7702 (without USB) and LA-7704 (with USB 1.1).
Converter to connect a Debug Cable to a TI-14 or TI-20-Compact connector which is used on many targets with processors from Texas Instruments Former name: Converter ARM-20 to TI-14 or TI-20-Compact
Debug probe suitable for most SoCs. This TRACE32 Product is a license carrier. It requires a suitable, programmed TRACE32 A-license. Requires Power Debug Interface USB 2.0/USB 3.0, PowerDebug Ethernet, PowerTrace Ethernet, PowerDebug II, PowerDebug PRO, PowerDebug E40. or PowerDebug X50 Voltage range 0.4V to 5V
Supports Arm Cortex-M cores and SecurCore SC000/SC300 trace support ETM Cortex-M via ETB included GTM and IPU debugging included IDC20A debug cable supports 5-pin standard JTAG, cJTAG and Serial Wire Debug Port, (0.4V - 5V) Includes software for Windows, Linux and macOS cJTAG and SWD require PowerDebug Interface USB 2.0/USB 3.0, PowerDebug Ethernet, PowerTrace, PowerDebug II PowerDebug PRO, PowerDebug E40 or PowerDebug X50