Product Catalogue
Find TRACE32 product
Converter 20 pin IDC20A to RL78 14 pin Renesas Former name: Converter ARM-20 to RL78-14
Converter to connect an IDC20A Debug Cable to a 16 pin PowerPC connector (PPC4xx)
Converter from MIPI34 connector on CombiProbe for Intel x86/x64 to FPC 41pin (Panasonic) connector Adapter for the Intel Medfield Smartphone Reference Platform
Converter to connect the ARM Debug Cable or the CombiProbe to a Mictor connector on the target. This is needed if you want to debug without a Preprocessor and if there is only a Mictor connector on the target. The trace signals of the CombiProbe are connected to the lowest four trace signals of the Mictor (ETMv3 pinout, continuous mode). But tracing is normally no use case due to the bandwidth limitations of the CombiProbe. Former name: ARM Conv. ARM-20/MIPI-34 to Mictor-38
Converter from IDC20A connector to Altera 10-pin (Byteblaster) or RISC-V 10-pin Target connector pitch can be 2.54mm or 1.27mm (half size)
Converter 20 pin IDC20A to 78K0R 16 pin NEC Former name: Converter ARM-20 to 78K-16
Converter from XDP 60 pin to MIPI 60 pin on target for ITP 60 pin to MIPI 60 pin (Intel)
Preprocessor for ST40 with AUD, 200 MHz clock speed with 36-pin Yamaichi connector Requires LA-7985 for 14 pin AUD connector voltage range 3.0V to 3.6V Requires PowerTrace Version 6 or higher or PowerTrace II / III
Preprocessor for NIOS-II, 150 MHz DDR clock speed, with MICTOR38 connector requires PowerTrace voltage range 1.5V to 5.0V
Converter Mictor connector to GPIO header of XILINX ML403/ML501 for Preprocessor for MicroBlaze (LA-3803) Preprocessor for Beyond AUTOFOCUS II (LA-3908)
Converter Mictor connector to FX2 header of XILINX Spartan3EStarter for Preprocessor for MicroBlaze (LA-3803)
Converter Mictor connector to trace header of XILINX Spartan3ADSP1800Starter for Preprocessor for MicroBlaze (LA-3803)
JTAG Adapter Spartan3 Xilinx MicroBlaze 16 pin to 6 pin Boards: EVB Spartan3EStarter Kit; EVB S3ADSP1800A
Converter to connect an ARM Preprocessor (up to 32-bit ETMv3) and a CombiProbe (STM/STP) to a MIPI-60 connector on the target. This converter is designed for L8540 from ST Ericsson.
Converter to connect an AutoFocus II Preprocessor with MICTOR-38 and an IDC20A Debug Cable to MIPI-10/-20T/-34. Enables the AutoFocus II Preprocessor to receive trace data from the 4-bit wide trace port of a MIPI-20T target connector. The converter is configured for MIPI-20T via 0 Ohm resistors. By soldering the resistors differently MIPI-34 can be supported as well. You can get the same converter pre-configured for MIPI-34 by ordering LA-3842 Converter Mictor-38/IDC20A to MIPI-34.
Converter to connect an ARM Preprocessor (up to 24-bit PTM/ETMv3) and up to three CombiProbes (3x STM/STP) to a MIPI-60 connector on the target. This converter is designed for U8500/U5500 from ST Ericsson.
Converter to connect an ARM Preprocessor (up to 18-bit PTM) and one CombiProbe (STM; two connection options) or a Debug Cable to a MIPI-60 connector on the target. This converter is designed for OMAP4xxx based boards from Texas Instruments. Former name: OMAP4 Conv. 2xMictor/ARM20/MIPI34 to MIPI60
Converter to connect an ARM Preprocessor and a CombiProbe to a Mictor connector on the target. This converter is designed for the OMAP3503 board from Spectrum Digital. The upper ETM signals on the Mictor can alternatively be used for system trace (SDTI).
ARM Converter to connect an ARM Preprocessor with one Mictor-38 for 16-bit ETMv3 and one CombiProbe for a 4-bit system trace port to a MIPI-60 connector on the target