Product Catalogue

Adapter for debugging over a CAN bus with up to 8 Mbit/s supporting DAP over CAN Physical Layer (DXCPL), DAP over CAN Message (DXCM) and more. Includes a removable CAN termination resistor (120 Ohm). Requires an AUTO26 Debug Cable V3 (LA-3011), AUTO26 Debug Cable V2 (LA-3010), or a CombiProbe2 with AUTO26 Whisker (LA-3081).

CAN termination (120 Ohm) with one female and one male D-Sub-9 connector connects all pins between both connectors with 120 Ohm resistor between line 2 and 7.

Adapter for debugging over a CAN bus with up to 1 Mbit/s supporting DAP over CAN Physical Layer (DXCPL) and more, with internal termination resistor. Usage with PowerDebug E40 / X50 / PRO requires one of the following: LA-3203 Debugger for TriCore AUTO26 (PACK), LA-3081 CombiProbe 2 for AUTO26 (PACK), LA-2707 Debugger for TriCore Automotive PRO (EOL). Usage with PowerDebug USB 3 / USB 2 / Ethernet / II requires one of the following:: LA-3203 Debugger for TriCore AUTO26 (PACK), LA-3081 CombiProbe 2 for AUTO26 (PACK), LA-2707 Debugger for TriCore Automotive PRO (EOL). LA-3737 Debugger for TriCore Automotive (EOL), LA-7756 Debugger for TriCore Standard (16-pin) (EOL).

Developer Tool Operational Verification and Validation Cases and Procedures (TOVVCP)

Converter to connect the CombiProbe to a SD or Micro SD card connector in case the signals alternatively provide debug functionality

Supports ARC EM/HS/EV/VPX, ARC 600/700, ARCtangent-A4/A5 Please add the base serial number of your existing debug cable to your order. LA-3750A in LA-3737 Debugger for TriCore Automotive can not be used to debug a stand-alone ARC chip LA-3750A can not be programmed on LA-7756 Debugger for TriCore Standard

Converter from a MIPI20T to a MIPI34 connector, designed to connect a MIPI20T-HS Whisker (from a CombiProbe or MicroTrace) to a target with MIPI34 connector. Can be used for debugging with optional 4-bit trace if a MIPI34 connector is mounted on the target. There is a pin header to optionally receive trace signals from elsewhere. Can be used to connect the debug signals of a MIPI20T-HS Whisker to an AUTOFOCUS II MIPI preprocessor or a PowerTrace Serial.

Converter from IDC20A and HSSTP to R-Car H3 Starter Kit from Renesas Former name: Conv. ARM-20/Samtec40 HSSTP to RCAR-H3-SKIT

Converter from IDC20A connector to Altera 10-pin (Byteblaster) or RISC-V 10-pin Target connector pitch can be 2.54mm or 1.27mm (half size)

Converter from IDC20A connector to MCHP FlashPro socket Target connector pitch can be 2.54mm or 1.27mm (half size) Usable for PolarFire SoC Icicle Kit

Universal debug controller with USB 3.0 for Windows/Linux/macOS can be used for all TRACE32 Debug Cable and for the TRACE32 CombiProbe requires TRACE32 software DVD 2013/02 or newer

Converter to connect an ARM Preprocessor and a CombiProbe to a Mictor connector on the target. This converter is designed for the OMAP3503 board from Spectrum Digital. The upper ETM signals on the Mictor can alternatively be used for system trace (SDTI).

Converter to connect an AutoFocus II Preprocessor with MICTOR-38 and an IDC20A Debug Cable to MIPI-10/-20T/-34. Enables the AutoFocus II Preprocessor to receive trace data from the 4-bit wide trace port of a MIPI-20T target connector. The converter is configured for MIPI-20T via 0 Ohm resistors. By soldering the resistors differently MIPI-34 can be supported as well. You can get the same converter pre-configured for MIPI-34 by ordering LA-3842 Converter Mictor-38/IDC20A to MIPI-34.

Converter to connect an AutoFocus II Preprocessor with MICTOR-38 and an IDC20A Debug Cable to MIPI-10/-20/-34. Enables the AutoFocus II Preprocessor to receive trace data from the 4-bit wide trace port of a MIPI-34 target connector. The converter is configured for MIPI-34 via 0 Ohm resistors. By soldering the resistors differently MIPI-20T can be supported as well. You can get the same converter pre-configured for MIPI-20T by ordering LA-3809 Converter Mictor-38/IDC20A to MIPI-20T.

Converter for MIPS-EJTAG 14 pins to 24 pins to support IDT processors IMPORTANT: This adpater can also be used for 20 pin target connections, but a separate wire for VCC is required. Please ask your local distributor.

Debug solution for RISC-V 32-bit standard core(s). Concurrent debugging of two or more RISC-V 32-bit standard cores requires a License for Multicore Debugging MicroTrace (LA-7960N). Can not be upgraded to include support for other core architectures.

Converter from a MIPI20T to a MIPI60 connector, designed to connect a MIPI20T-HS Whisker (from a CombiProbe or MicroTrace) to a target with MIPI60 connector. Can be used for debugging with optional 4-bit trace if a MIPI60 connector is mounted on the target.

Universal BDM debug and JTAG controller, 200 MHz PowerPC, 64 MB DRAM, High-Speed FPGA USB 2.0 (Win98/2000/XP/Linux) included can be upgraded to PowerTrace by LA-7691 (512MByte) Out of production since November 2014

General documentation of the TRACE32 Tool Qualification Support-Kit. Includes general documentation and the following test suites: - Debug - Coverage Includes additionally test suite - TRACE32 TriCore Instruction Set Simulator which requires LA-8096L 1 User Floating Lic. ISS Test Suite TriCore - TRACE32 M68K Instruction Set Simulator which requires LA-8097L 1 User Floating Lic. ISS Test Suite 68K Each test suite contains a set of test cases, corresponding test case documentation and results. Downloadable after registration in TRACE32 TQSK Customer Portal For Windows, Linux, and macOS.

Legacy Trace Port Recorder with 2 GigaByte trace memory and a streaming rate up to 180 MByte/s. Requires a suitable trace preprocessor or Nexus Adapter. Requires PowerDebug X50, PowerDebug PRO, or PowerDebug II. Can be extended with a Logic-Analyzer-Probe (LA-7945) or Analog-Probe (LA-7949).