200 mm flex extension for Mictor 76pin connector
60 mm flex extension for MICTOR 38 pin connector
horizontal-vertical
55 mm flex extension for MICTOR 38 pin connector
vertical-vertical
75 mm flex extension for 2.54 mm 20 pin connector
with shrouded post-strips horizontal-horizontal
75 mm flex extension for 2.54 mm 20 pin connector
horizontal-horizontal
140 mm flex extension 60 pin SAMTEC QTH-QSH,
e.g. Tricore with SAMTEC QTH connector LA-7928
e.g. ARM-ETM/AUTOFOCUS 600 MIPI LA-7993
e.g. Preprocessor for Intel® PT AUTOFOCUS MIPI60 LA-3907
similar in design as LA-1238, LA-1248 and LA-1249
170 mm flex extension for
60 pin SAMTEC BTH-BSH connector
e.g. XDP60 Intel® x86/x64 debugger
140 mm flex extension for
20 pin SAMTEC ERM-ERF connector
e.g. Nexus Autofocus
140 mm flex extension for
50 pin SAMTEC ERM-ERF connector
e.g. Nexus Autofocus
180 mm flex extension for
40 pin SAMTEC ERM-ERF connector
incl. CCS-female-female adaption
e.g. Preproc. for ARM-ETM/HSSTP HF-Flex
LA-7988
290 mm flex extension for
34 pin SAMTEC ERM-ERF connector
partial differential pairs!
290 mm flex extension for
22 pin SAMTEC ERM-ERF connector
partial differential pairs!
500 mm flex extension for
40 pin SAMTEC ERM8-ERF8 connector
e.g. for PowerTrace Serial
330 mm flex extension 60 pin SAMTEC QTH-QSH,
e.g. Tricore with SAMTEC QTH connector LA-7928
e.g. ARM-ETM/AUTOFOCUS 600 MIPI LA-7993
e.g. Preprocessor for Intel® PT AUTOFOCUS MIPI60 LA-3907
similar in design as LA-1228, LA-1248 and LA-1249
500 mm flex extension for PowerTrace Serial
80 pin SAMTEC ERM8-ERM8 connector
200 mm flex extension 60 pin SAMTEC QTH-QSH,
e.g. WHISKER-QP-MIPI60-Q LA-4611
e.g. Tricore with SAMTEC QTH connector LA-7928
e.g. ARM-ETM/AUTOFOCUS 600 MIPI LA-7993
e.g. Preprocessor for Intel® PT AUTOFOCUS MIPI60 LA-3907
similar in design as LA-1228, LA-1238 and LA-1249
610 mm flex extension 60 pin SAMTEC QTH-QSH,
e.g. WHISKER-QP-MIPI60-QL LA-4612
e.g. Tricore with SAMTEC QTH connector LA-7928
e.g. ARM-ETM/AUTOFOCUS 600 MIPI LA-7993
e.g. Preprocessor for Intel® PT AUTOFOCUS MIPI60 LA-3907
similar in design as LA-1228, LA-1238, and LA-1248
110 mm flex extension for Mictor 38pin connector
200 mm flex extension for Mictor 38pin connector
Wall Mount Power Supply
for Power Debug Module USB and uTrace
Desktop Power Supply
For PowerDebug PRO, PowerTrace II and PowerTrace Serial
and TRACE32 FIRE
USB3.0 special cable for DCI.DbC debugging
type A connector on both sides
Adapter 14 pin 100 mil to 50 mil with cable.
50 mil connector is a 16 pin connector on target.
Pin 15 and 16 are not connected.
Adapter 20 pin 100 mil to 50 mil with cable.
Purpose: Use 20-pin Debug Cable with smaller target
connector. In case of ARM Debug Cable better use
MIPI-10 or MIPI-20 for new designs.
Adapter 16 pin 100 mil to 50 mil with cable.
Adapter 10 pin 100 mil to 50 mil with cable.
Replacement part 10 cm
Half Size Adapter (LA-2100)
Replacement part 10 cm
Half Size Adapter (LA-2101)
Replacement part 10 cm
Half Size Adapter (LA-2102)
Replacement part 5 cm
Half Size Adapter (LA-2103)
Converter from Automotive Debug Cable (26-pin)
to 14 Pin RH850 connector on target
for
LA-2709 (Debugger for RH850/V850 Automotive PRO)
LA-3739 (Debugger for RH850 Automotive)
Converter from 14 pin debug connector for RH850 to AUTO26
use with
LA-3719 (Debugger for RH850)
to connect to targets designed for
LA-2709 (Debugger for RH850/V850 Automotive PRO)
LA-3739 (Debugger for RH850 Automotive)
Converter from 14 pin debug connector for RH850 to
20 pin N-Wire for V850
use with
LA-3719 (Debugger for RH850)
supports AVR8
includes software for Windows, Linux and MacOSX
voltage range 1.8V to 5.5V
supports AVR8
please add the serial number of the base debug
cable to your order
JTAG Debugger for ARP32 Add.
supports ARP32
includes software for Windows, Linux and MacOSX
voltage range 1.8V to 5.5V
supports TriCore, PCP and GTM debugging included
supports JTAG and DAP
includes software for Windows, Linux and MacOSX
requires Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, Power Debug II or
PowerDebug PRO
Automotive Debug Cable 26-pin
Usage of LA-3912 Preproc. TriCore HSTP HF-Flex
requires LA-3829
voltage range 0.9V to 5.5V
supports Qorivva MPC5xxx/SPC5xxx (e200 cores)
and Freescale PX SERIES processors
eTPU, GTM and SPT debugging included
Concurrent debugging of multiple e200 cores on
multicore processors requires a
License for Multicore Debugging (LA-7960X)
(not necessary for lockstep mode)
includes software for Windows, Linux and MacOSX
requires
Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, Power Debug II or
PowerDebug PRO
includes LA-3873 (Conv. AUTO26 to JTAG14 OnCE)
voltage range 0.9V to 5.5V
supports RH850 via JTAG, LPD4
ICU-M core support included
supports V850 via NWIRE
includes software for Windows, Linux and MacOSX
requires
Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, Power Debug II or
PowerDebug PRO
debug cable with 26 pin connector
voltage range 0.9V to 5.5V
supports NIOS-II
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 20 pin connector
voltage range 1.8V to 3.6V
supports RISC-V
MIPI10 / MIPI20 connector on the target required:
LA-3770 ARM Converter ARM-20 to MIPI-10/20/34
ALTERA-10/RISCV-10 connector on the target required:
LA-3863 Converter ARM-20 to ALTERA-10/RISCV-10
includes software for Windows, Linux and MacOSX
requires Power Debug Module
voltage range 1.8V to 3.6V
supports RISC-V
only suitable for debug cables newer than 07/2008
MIPI10 / MIPI20 connector on the target required:
LA-3770 ARM Converter ARM-20 to MIPI-10/20/34
ALTERA-10/RISCV-10 connector on the target required:
LA-3863 Converter ARM-20 to ALTERA-10/RISCV-10
includes software for Windows, Linux and MacOSX
supports STM8
includes software for Windows, Linux and MacOSX
requires Power Debug Module
voltage range 1.8V to 3.6V
Converter to connect an ARM Debug Cable to a MIPS-14 connector
on the target
Converter to connect a MIPS Debug Cable to an ARM-20 connector
on the target
Converter from Intel MIPI60-Cv2 to Intel MIPI60-C pin-out on target
Converter from Intel MIPI60-Cv2 to MIPI34 pin-out on target
Converts termination scheme Intel
(50 Ohm parallel termination at receiver)
to termination scheme ARM
(50 Ohm series termination at sender)
Support for JTAG/SWD
Maps Intel specific debug signals to MIPI34 pins.
Default mapping:
Intel PREQ ->
DBGREQ (pin 18 on MIPI34)
Intel PRDY ->
DBGACK (pin 20 on MIPI34)
Intel HOOK6 (PMODE) ->
RTCK (pin 12 on MIPI34)
Intel HOOK0 (PowerGood) ->
BCE (pin 14 on MIPI34)
Intel HOOK7 (ResetOut) ->
RESET (pin 10 on MIPI34)
TVREF (trace reference voltage) ==
DVREF (debug reference voltage)
For other possible options,
please contact Lauterbach.
Combination of two converters to adapt from Intel MIPI60-Cv2
to MIPI20 pin-out on target
ARM Converter MIPI-20T to ARM-20
Converter from MIPI-20T to ARM-20
supports STM8 4 pin connector
supports the SPI Programming Interface of Atmel AVR8 Chips
JTAG Converter 26-pin Automotive Debug Cable
(PPC/ TriCore/RH850) to 10-pin ECU14
for
LA-2707 (Debugger for TriCore Automotive PRO)
LA-2708 (Debugger for MPC5xxx Automotive PRO)
LA-2709 (Debugger for RH850/V850 Automotive PRO)
LA-2713 (Debug-Bundle MPC5xxx/TriCore Automotive PRO)
LA-2714 (Debug-Bundle TriCore/RH850 Automotive PRO)
LA-3736 (JTAG Debugger for MPC5xxx Automotive)
LA-3737 (JTAG Debugger for TriCore Automotive)
LA-3738 (Debugger-Bundle MPC5xxx/TriCore Automotive)
LA-3739 (Debugger for RH850/V850 Automotive)
LA-3753 (Debugger-Bundle TriCore/RH850 Automotive)
ARM Converter ARM-20 or MIPI-20 to 10-pin ECU14
Converter 26-pin Automotive Debug Cable
to ARM20 or TI14
Supports STRED cores
Multicore debugging included
includes software for Windows, Linux and MacOSX
requires Power Debug Module
voltage range 0.4V to 5.2V
Supports STRED cores
Multicore debugging included
only suitable for debug cables newer than 07/2008
please add the base serial number of your debug
cable to your order
includes software for Windows, Linux and MacOSX
Trace License for STRED (Debug Cable)
Supports On-chip Trace for STRED
please add the base serial number of your debug
cable to your order
supports eSi-RISC Core
includes software for Windows, Linux and MacOSX
requires Power Debug Module or PowerTrace
debug cable with 16 pin connector
voltage range 1.8V to 3.6V
supports eSi-RISC Core
Multicore debugging included
only suitable for debug cables newer than 07/2008
please add the base serial number of your debug
cable to your order
includes software for Windows, Linux and MacOSX
JTAG Debugger for PRU Add.
supports PRU
includes software for Windows, Linux and MacOSX
JTAG Debugger for Mico32 (ICD)
Supports Mico32 cores
includes software for Windows, Linux and MacOSX
requires Power Debug Module
voltage range 0.4V to 5.2V
JTAG Debugger for Mico32 Add.
Supports Mico32 cores
only suitable for debug cables newer than 07/2008
please add the base serial number of your debug
cable to your order
includes software for Windows, Linux and MacOSX
Debugger for Meta (ICD)
Supports META cores
Multicore debugging included
includes software for Windows, Linux and MacOSX
requires Power Debug Module
voltage range 0.4V to 5.2V
JTAG Debugger for META Add.
Supports META cores
Multicore debugging included
only suitable for debug cables newer than 07/2008
please add the base serial number of your debug
cable to your order
includes software for Windows, Linux and MacOSX
supports C7000
only suitable for debug cables newer than 07/2008
please add the base serial number of your debug
cable to your order
supports dsPIC33C (0.4 V - 5 V)
includes software for Windows, Linux and MacOSX
requires Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, Power Debug II or
PowerDebug PRO
Automotive-Pro Debug Cable 26-pin
supports dsPIC33C
Adaptation to MICROCHIP-8 requires
LA-2773 Conv. AUTO26 to MICROCHIP-8
LA-1949 Automotive HALF-SIZE-CABLE 26-26
only suitable for debug cables newer than 07/2008
please add the base serial number of your debug
cable to your order
includes software for Windows, Linux and MacOSX
Trace License for C7000 DSP (Debug Cable)
Supports C7000 trace
please add the base serial number of your debug
cable to your order
Whisker for dsPIC
26-pin Automotive Connector
voltage range 0.4V to 5.2V
Converter from ARM-20 to 12 pin PMOD connectors with the
JTAG pinout from SiFive.
PMOD is an open standard defined by Digilent for peripherals used with
FPGAs or microcontrollers.
The PMOD pinout of this adapter does ONLY work with targets that use
the pinout that was defined by SiFive. So it is not a general/official
RISC-V pinout. In case of FPGA boards, the pinout depends on the used
FPGA image.
Trace License for RISC-V (Debug Cable)
Supports On-chip Trace for RISC-V
tested for SiFive Nexus IP
tested for UltraSoc Trace Encoder IP
other IP on request
please add the base serial number of your debug
cable to your order
ARM Conv. ARM-20 to MIPI-34 PowerTrace Serial
converter to connect a 20pin Debug Cable to
34 pin DEBUG connector on PowerTrace Serial,
MIPI-34 connector does not have key pin
Converter JTAG-RH850 of
LA-3719 (Debugger RH850 14pin)
and from AUTO26 of
LA-2709 (Debugger for RH850/V850 Automotive PRO)
LA-3739 (Debugger RH850 Automotive)
and Samtec 40 pin of
LA-3943 (Preproc. RH850 HSTP HF-Flex)
to Samtec ERF 34-pin RH850 pinout
Includes Samtec 34-pin flex extension
JTAG Debugger for SDMA Add.
supports SDMA
includes software for Windows, Linux and MacOSX
Converter from Automotive Debug Cable (26-pin)
to MICROCHIP-8
for
LA-2760 (Debugger for Microchip PIC)
Conv. Samtec40 HSSTP to RCAR-H3-Starterkit
Converter from JTAG ARM20 and
HSSTP to R-Car H3 Starter Kit from Renesas
Floating license to use the TRACE32 Instruction Set
Simulator for automated tests via script language
PRACTICE or via the TRACE32 Remote API
supports TriCore
for Windows32, Windows64, Linux32, Linux64
and Solaris, other platforms on request
floating license via RLM (Reprise License Manager)
Please add the RLM HostID of the license server
to your order (please see our FAQ)
Floating license to use the TRACE32 Instruction Set
Simulator for automated tests via script language
PRACTICE or via the TRACE32 Remote API
supports PowerPCs
for Windows32, Windows64, Linux32, Linux64
and Solaris, other platforms on request
floating license via RLM (Reprise License Manager)
Please add the RLM HostID of the license server
to your order (please see our FAQ)
Floating license to use the TRACE32 Instruction Set
Simulator for automated tests via script language
PRACTICE or via the TRACE32 Remote API
supports RH850/V850
for Windows32, Windows64, Linux32, Linux64
and Solaris, other platforms on request
floating license via RLM (Reprise License Manager)
Please add the RLM HostID of the license server
to your order (please see our FAQ)
Floating license to use the TRACE32 Instruction Set
Simulator for automated tests via script language
PRACTICE or via the TRACE32 Remote API
supports 78K0R/RL78
for Windows32, Windows64, Linux32, Linux64
and Solaris, other platforms on request
floating license via RLM (Reprise License Manager)
Please add the RLM HostID of the license server
to your order (please see our FAQ)
Floating license to use the TRACE32 Instruction Set
Simulator for automated tests via script language
PRACTICE or via the TRACE32 Remote API
supports ARM/Cortex
for Windows32, Windows64, Linux32, Linux64
and Solaris, other platforms on request
floating license via RLM (Reprise License Manager)
Please add the RLM HostID of the license server
to your order (please see our FAQ)
Floating license to use the TRACE32 Instruction Set
Simulator for automated tests via script language
PRACTICE or via the TRACE32 Remote API
supports Intel x86/x64
for Windows32, Windows64, Linux32, Linux64
and Solaris, other platforms on request
floating license via RLM (Reprise License Manager)
Please add the RLM HostID of the license server
to your order (please see our FAQ)
Floating license to use the TRACE32 Instruction Set
Simulator for automated tests via script language
PRACTICE or via the TRACE32 Remote API
supports MicroBlaze
for Windows32, Windows64, Linux32, Linux64
and Solaris, other platforms on request
floating license via RLM (Reprise License Manager)
Please add the RLM HostID of the license server
to your order (please see our FAQ)
Floating license to use the TRACE32 Instruction Set
Simulator for automated tests via script language
PRACTICE or via the TRACE32 Remote API
supports Nios II
for Windows32, Windows64, Linux32, Linux64
and Solaris, other platforms on request
floating license via RLM (Reprise License Manager)
Please add the RLM HostID of the license server
to your order (please see our FAQ)
Floating license to use the TRACE32 Instruction Set
Simulator for automated tests via script language
PRACTICE or via the TRACE32 Remote API
supports Beyond
for Windows32, Windows64, Linux32, Linux64
and Solaris, other platforms on request
floating license via RLM (Reprise License Manager)
Please add the RLM HostID of the license server
to your order (please see our FAQ)
Floating license to use the TRACE32 Instruction Set
Simulator for automated tests via script language
PRACTICE or via the TRACE32 Remote API
supports MSP430
for Windows32, Windows64, Linux32, Linux64
and Solaris, other platforms on request
floating license via RLM (Reprise License Manager)
Please add the RLM HostID of the license server
to your order (please see our FAQ)
Floating license to use the TRACE32 Instruction Set
Simulator for automated tests via script language
PRACTICE or via the TRACE32 Remote API
supports 68k and ColdFire
for Windows32, Windows64, Linux32, Linux64
and Solaris, other platforms on request
floating license via RLM (Reprise License Manager)
Please add the RLM HostID of the license server
to your order (please see our FAQ)
Floating license to use the TRACE32 Instruction Set
Simulator for automated tests via script language
PRACTICE or via the TRACE32 Remote API
supports C166
for Windows32, Windows64, Linux32, Linux64
and Solaris, other platforms on request
floating license via RLM (Reprise License Manager)
Please add the RLM HostID of the license server
to your order (please see our FAQ)
Floating license to use the TRACE32 Instruction Set
Simulator for automated tests via script language
PRACTICE or via the TRACE32 Remote API
supports S12, S12X, S12Z, HC12
for Windows32, Windows64, Linux32, Linux64
and Solaris, other platforms on request
floating license via RLM (Reprise License Manager)
Please add the RLM HostID of the license server
to your order (please see our FAQ)
Floating license to use the TRACE32 Instruction Set
Simulator for automated tests via script language
PRACTICE or via the TRACE32 Remote API
supports SH1/SH2/SH3/SH4
for Windows32, Windows64, Linux32, Linux64
and Solaris, other platforms on request
floating license via RLM (Reprise License Manager)
Please add the RLM HostID of the license server
to your order (please see our FAQ)
Floating license to use the TRACE32 Instruction Set
Simulator for automated tests via script language
PRACTICE or via the TRACE32 Remote API
supports Hexagon
for Windows32, Windows64, Linux32, Linux64
and Solaris, other platforms on request
floating license via RLM (Reprise License Manager)
Please add the RLM HostID of the license server
to your order (please see our FAQ)
Floating license to use the TRACE32 Instruction Set
Simulator for automated tests via script language
PRACTICE or via the TRACE32 Remote API
supports TMS320C28X
for Windows32, Windows64, Linux32, Linux64
and Solaris, other platforms on request
floating license via RLM (Reprise License Manager)
Please add the RLM HostID of the license server
to your order (please see our FAQ)
Floating license to use the TRACE32 Instruction Set
Simulator for automated tests via script language
PRACTICE or via the TRACE32 Remote API
supports MIPS32 and MIPS64
for Windows32, Windows64, Linux32, Linux64
and Solaris, other platforms on request
floating license via RLM (Reprise License Manager)
Please add the RLM HostID of the license server
to your order (please see our FAQ)
Floating license to use the TRACE32 Instruction Set
Simulator for automated tests via script language
PRACTICE or via the TRACE32 Remote API
supports OAK, Teak and Teaklite
for Windows32, Windows64, Linux32, Linux64
and Solaris, other platforms on request
floating license via RLM (Reprise License Manager)
Please add the RLM HostID of the license server
to your order (please see our FAQ)
Addtional year of software warranty
includes free software updates
and support, by telephone or email,
for TRACE32 Instruction Set Simulator
Please add the serial number of the TRACE32
Instruction Set Simulator to your order
Allows Processor-in-the-Loop Simulation for MATLAB
Architecture independent license
for Windows32, Windows64, Linux32, Linux64
and Solaris, other platforms on request
All TRACE32 Front-End instances have to run
on the same host
Floating license via RLM (Reprise License Manager)
Please add the RLM HostID of the license server
to your order (please see our FAQ)
License for PIL Simulation (Cable)
Allows Processor-in-the-Loop Simulation for MATLAB
Architecture independent license
requires a valid software guarantee or a valid
software maintenance key
please add the base serial number of your debug
cable to your order
Universal debug controller with
USB 3.0 for Windows/Linux/MacOSX
applicable for all TRACE32 debug cables
requires TRACE32 software DVD 2013/02 or newer
Galvanic Isolation for Debug Cable
Galvanic isolation
for ARM debug cable
for automotive debug cable
Components rated to IEC60950-1 (600 V working voltage)
Universal debug controller,
1 Gbit Ethernet and
USB 3.0 (Windows/Linux/MacOSX)
PowerTrace Serial 4 GigaByte for ARM-ETM
Serial Trace Port Controller with 4 Giga Byte Trace Memory
for ARM-ETM
requires PowerDebug II Ethernet or PowerDebug PRO
requires accessories as LA-3521 or LA-3522
Host requirements:
USB 3.0 or 1000 MBit Ethernet interface,
4.0 GigaByte RAM
voltage range 0.15V to 1.25V
Trace License ARM-ETM for Power Trace Serial
Supports off-chip ETM/PTM trace port for
ARM/Cortex
if applied to Power Trace Serial
please add the serial number of the Power Trace Serial to
your order
Accessories for PTSerial for ARM-ETM 1-6Lanes
Accessories for PTSerial for ARM-ETM 7-8Lanes
PTSERIAL-PCIe x4 Slot-Card-Converter
Active slot card adapter for up to 4-lanes PCIe
Converts standard PCIe slot card format to 80pin ERF8
for PowerTrace Serial
requires
LA-1239 Flex Ext. for SAMTEC 80 pin ERM8-ERM8 series
Pinout conform to PCI-Express x4 Connector Pin-Out
PTSERIAL-PCIe x8 Slot-Card-Converter
Active slot card adapter for up to 8-lanes PCIe
Converts standard PCIe slot card format to 80pin ERF8
for PowerTrace Serial
requires
LA-1239 Flex Ext. for SAMTEC 80 pin ERM8-ERM8 series
Pinout conform to PCI-Express x8 Connector Pin-Out
PTSERIAL-MiniPCIe x1 Slot-Card-Converter
Passive slot card adapter for 1lane
Converts standard Mini-PCIe slot card format to 80pin ERF8
for PowerTrace Serial
requires
LA-1239 Flex Ext. for SAMTEC 80 pin ERM8-ERM8 series
Pinout conform to PCI-Express x1 Connector Pin-Out
PTSERIAL-PCIe x1 Slot-Card-Converter
Active slot card adapter for up to 1-lanes PCIe
Converts standard PCIe slot card format to 80pin ERF8
for PowerTrace Serial
requires
LA-1239 Flex Ext. for SAMTEC 80 pin ERM8-ERM8 series
Pinout conform to PCI-Express x1 Connector Pin-Out
PowerTrace Serial 4 GigaByte for CEVA-X ETM
Serial Trace Port Controller with 4 Giga Byte Trace Memory
for CEVA-X ETM
requires PowerDebug II Ethernet or PowerDebug PRO
Host requirements:
USB 3.0 or 1000 MBit Ethernet interface,
4.0 GigaByte RAM
voltage range 0.15V to 1.25V
Trace Lic. CEVA-X ETM for Power Trace Serial
Supports off-chip trace port for
CoreSight CEVA-X
if applied to Power Trace Serial
please add the serial number of the Power Trace Serial to
your order
PowerTrace Serial 4 GigaByte for RISC-V
Serial Trace Port Controller with 4 Giga Byte Trace Memory
for RISC-V
tested for SiFive Nexus IP
tested for UltraSoc Trace Encoder IP
other IP on request
requires PowerDebug II Ethernet or PowerDebug PRO
Host requirements:
USB 3.0 or 1000 MBit Ethernet interface,
4.0 GigaByte RAM
voltage range 0.15V to 1.25V
Trace Lic. RISC-V for Power Trace Serial
Supports off-chip trace port
for RISC-V
tested for SiFive Nexus IP
tested for UltraSoc Trace Encoder IP
other IP on request
if applied to Power Trace Serial
please add the serial number of the Power Trace Serial to
your order
PowerTrace Serial 4 GigaByte for ARC
Serial Trace Port Controller with 4 Giga Byte Trace Memory
for ARC Real-Time Trace (ARC RTT)
requires PowerDebug II Ethernet or PowerDebug PRO
Host requirements:
USB 3.0 or 1000 MBit Ethernet interface,
4.0 GigaByte RAM
voltage range 0.15V to 1.25V
Trace Lic. ARC for Power Trace Serial
Supports off-chip trace port
for ARC Real-Time Trace (ARC RTT)
if applied to Power Trace Serial
please add the serial number of the Power Trace Serial to
your order
PowerTrace Serial 4 GigaByte MPC57xx/SPC57XX
Serial Trace Port Controller with 4 Giga Byte Trace Memory
for MPC57xx/SPC57XX
Required converter:
- Samtec34 on target requires LA-3871:
Converter Samtec40 HSTP+AUTO26+JTAG14 to Samtec34
including Samtec 34-pin flex extension cable
- Samtec22 on target requires LA-3872:
Converter Samtec40 HSTP+AUTO26+JTAG14 to Samtec22
including Samtec 22-pin flex extension cable
requires PowerDebug II Ethernet or PowerDebug PRO
Host requirements:
USB 3.0 or 1000 MBit Ethernet interface,
4.0 GigaByte RAM
voltage range 0.15V to 1.25V
Trace License MPC57xx for Power Trace Serial
Supports off-chip trace port for
MPC57xx/SPC57XX
if applied to Power Trace Serial
please add the serial number of the Power Trace Serial to
your order
License for PCI Express
enable tracing via PCI Express
Architecture independent license
please add the serial number of your PowerTrace Serial to your order
PowerTrace Serial 4 GigaByte for TriCore AGBT
Serial Trace Port Controller with 4 Giga Byte Trace Memory
for TriCore AGBT
requires PowerDebug II Ethernet or PowerDebug PRO
Host requirements:
USB 3.0 or 1000 MBit Ethernet interface,
4.0 GigaByte RAM
voltage range 0.15V to 1.25V
Trace License TriCore for Power Trace Serial
Supports AGBT trace port for
Tricore
if applied to Power Trace Serial
please add the serial number of the Power Trace Serial to
your order
AGBT Trace Adapter for PowerTrace Serial
Adapter for PowerTrace Serial to support Tricore-AGBT trace ports
up to 4lanes,
requires LA-3555
PowerTrace Serial 4 GigaByte RH850
Serial Trace Port Controller with 4 Giga Byte Trace Memory
for RH850
requires PowerDebug II Ethernet or PowerDebug PRO
Host requirements:
USB 3.0 or 1000 MBit Ethernet interface,
4.0 GigaByte RAM
Supported speeds per lane:
8 lanes, 12.5Gbps each
voltage range 0.15V to 1.25V
Trace License RH850 for Power Trace Serial
Supports Aurora trace port for
RH850
if applied to Power Trace Serial
please add the serial number of the Power Trace Serial to
your order
RH850-34pin Debug&Trace Adapter for PT Serial
Adapter for PowerTrace Serial to support RH850 trace ports
up to 4lanes,
34pin target connector
requires LA-3560
RH850-40pin Debug&Trace Adapter for PT Serial
Adapter for PowerTrace Serial to support RH850 trace ports
up to 4lanes,
40pin target connector
requires LA-3560
PowerTrace Serial 4 GigaByte QorIQ PowerPC
Serial Trace Port Controller with 4 Giga Byte Trace Memory
for QorIQ PowerPC
converters for Samtec22 or Samtec46 have to be
ordered separately if required
requires PowerDebug II Ethernet or PowerDebug PRO
Host requirements:
USB 3.0 or 1000 MBit Ethernet interface,
4.0 GigaByte RAM
voltage range 0.15V to 1.25V
Trace Lic. QorIQ PowerPC Power Trace Serial
Supports Aurora trace port for
QorIQ PowerPC
if applied to Power Trace Serial
please add the serial number of the Power Trace Serial to
your order
Accessories for PTSerial MiniPCIe x1
Consists of
LA-3550X License for PCI Express
LA-1239 Flex Ext. for SAMTEC 80 pin ERM8-ERM8 series
LA-3526 PTSERIAL-MiniPCIe x1 Slot-Card-Converter
Accessories for PTSerial PCIe x4 Slot-Card
Consists of
LA-3550X License for PCI Express
LA-1239 Flex Ext. for SAMTEC 80 pin ERM8-ERM8 series
LA-3524 PTSERIAL-PCIe x4 Slot-Card-Converter
Universal Trace Port Controller,
512 MegaByte Trace Memory
Streaming rate up to 50 MByte/s
requires PowerDebug II Ethernet or PowerDebug PRO
Converter PowerTrace Serial to 40 pin AGBT
Adapter for PowerTrace Serial SERIAL PORT 1 (80-pin)
to 40-pin AGBT connector for TriCore Aurix
supports ST40 from STMicroelectronics
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 20 pin connector
supports CEVA-X
includes software for Windows, Linux and MacOSX
requires Power Debug Module or PowerTrace
debug cable with 20 pin connector
supports CEVA-X
please add the serial number of the base debug
cable to your order
supports ZSP500 Core (LSI)
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 20 pin connector
supports ZSP500 Core (LSI)
please add the serial number of the base debug
cable to your order
supports MSP430 via JTAG or Spy-Bi-Wire
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 14 pin connector
Measuring Adapter JTAG 20
Adapter to measure JTAG signals by a logic analyzer
or to disconnect single JTAG lines from the target
Converter V850-20 Pin to E1-14 Pin
supports RH850 via JTAG, LPD4, LPD1
ICU-M core support included
supports V850 via NWIRE
includes software for Windows, Linux and MacOSX
requires Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, Power Debug II or
PowerDebug PRO
debug cable with 14 pin connector
Converter to connect the ARM Debug Cable to a Mictor
connector on the target providing both debug and
trace signals. This is needed if you want to connect
the Debug Cable without a Preprocessor and if there
is only a Mictor on the target. Suitable for MMDSP
and ARC as well.
Converter 14 Pin JTAG/OnCE connector to Mictor38
on target for Qorivva MPC5xxx and SPC5xxx
Adapter to connect debug cable of
JTAG Debugger for StarCore (LA-7834)
to targets with JTAG connector that
use an ejector
Converter Mictor38 (NEXUS) connector to 14 Pin JTAG
on target for MPC5xxx
Converter to connect two ARM Debug Cable to one
connector on the target.
Old method to handle multicore debugging by using
two debugger hardware modules.
Conv. Mictor38/JTAG20 to 60 Pin CTOOLS
Converter Mictor38/20 Pin JTAG (ARM and TI)
to 60 Pin CTOOLS connector on target
Conv. 20 Pin JTAG to 60 Pin CTOOLS
Converter 20 Pin JTAG (ARM and TI)
to 60 Pin CTOOLS connector on target
(electrical same as LA-3729)
Conv. 60 Pin CTOOLS to 20 Pin JTAG con. swap
Converter 20 Pin JTAG swap (ARM and TI)
to 60 Pin CTOOLS connector on target
(electrical same as LA-3728)
supports MicroBlaze
includes software for Windows, Linux and MacOSX
requires Power Debug Module or PowerTrace
debug cable with 16 pin connector
supports MicroBlaze
requires
LA-3731 JTAG Converter to Xilinx Targe tAdapter 14
if a 16-pin PowerPC Debug Cable is used
LA-3881 Converter ARM-20 to XILINX-14
if a 20-pin ARM Debug Cable is used
please add the base serial number of your debug
cable to your order
Converter from PPC400 16 pins to Xilinx
PPC400/Microblaze 14 pins target adapter
supports XC800
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 16 pin connector
Support for onchip trace on RH850
please add the base serial number of your debug
cable to your order
supports (1.8V - 5.0V) MPC8641, MPC8641D and MPC8610
Concurrent debugging of both cores in
dual-core chip requires a
License for Multicore Debugging (LA-7960X)
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 16 pin connector
supports (1.8V - 5.0V) MPC86xx
requires a valid software guaranty or a valid
software maintenance key
not suitable for debug cables older than 02/2004
(blue ribbon cable)
please add the serial number of the base debug
cable to your order
supports Qorivva MPC5xxx/SPC5xxx (e200 cores)
and Freescale PX SERIES processors
eTPU, GTM and SPT debugging included
Concurrent debugging of multiple e200 cores on
multicore processors requires a
License for Multicore Debugging (LA-7960X)
(not necessary for lockstep mode)
includes software for Windows, Linux and MacOSX
requires
Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, Power Debug II or
PowerDebug PRO
includes LA-3873 (Conv. AUTO26 to JTAG14 OnCE)
Superseded by LA-2708 Debugger for MPC5xxx Automotive PRO
supports TriCore, PCP and GTM debugging included
supports JTAG and DAP
includes software for Windows, Linux and MacOSX
requires Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, Power Debug II or
PowerDebug PRO
Automotive Debug Cable 26-pin
Usage of LA-3912 Preproc. TriCore HSTP HF-Flex
requires LA-3829
Superseded by LA-2707 Debugger for TriCore Automotive PRO
debug cable with license bundle
includes software for Windows, Linux and MacOSX
requires
Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, PowerTrace, Power Debug II
or PowerDebug PRO
Automotive Debug Cable 26-pin
Superseded by LA-2713 Debug-Bundle MPC5xxx/TriCore Automotive PRO
supports RH850 via JTAG, LPD4
ICU-M core support included
supports V850 via NWIRE
includes software for Windows, Linux and MacOSX
requires
Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, Power Debug II or
PowerDebug PRO
debug cable with 26 pin connector
Superseded by LA-2709 Debugger for RH850/V850 Automotive PRO
supports Hexagon from Qualcomm
Multicore debugging included
includes software for Windows, Linux and MacOSX
requires Power Debug Module or PowerTrace
debug cable with 20 pin connector
supports Hexagon
please add the serial number of the base dongle
to your order
Supports ARMv8-A/R based Cortex-A and Cortex-R 32/64-bit cores
supports 5-pin standard JTAG, cJTAG and SWD,
(0.4 V - 5 V)
Multicore debugging included
includes software for Windows, Linux and MacOSX
requires Power Debug Module
cJTAG and SWD require
Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, PowerTrace, Power Debug II
or PowerDebug PRO
Supports ARMv8-A/R based Cortex-A and Cortex-R 32/64-bit cores
only suitable for debug cables newer than 07/2008
please add the base serial number of your debug
cable to your order
Supports ARMv8-A/R based Cortex-A and Cortex-R 32/64-bit cores
only suitable for debug cables newer than 07/2008
please add the base serial number of your debug
cable to your order
JTAG Debugger Lic. for APEX ADD.
supports APEX
includes software for Windows, Linux and MacOSX
only suitable for debug cables newer than 07/2008
please add the base serial number of your debug
cable to your order
supports CPU H8SX/1664 from Renesas
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 14 pin connector
supports CPU H8SX/1664 from Renesas
requires a valid software guaranty or a valid
software maintenance key
please add the serial number of the base debug
cable to your order
supports FREESCALE ColdFire+/V1 Family
includes software for Windows, Linux and MacOSX
requires Power Debug Module or PowerTrace
debug cable with 6 pin connector
JTAG/SPI Debugger for UBI32
supports UBI32
Multicore debugging included
includes software for Windows, Linux and MacOSX
requires Power Debug Module or PowerTrace
debug cable with 20 pin connector
JTAG/SPI Debugger License for UBI32 Add.
supports UBI32
Requires
LA-3864 Converter ARM-20 to UBI32-10
if an UBI32-10 connector is used on the target
only suitable for debug cables newer than 07/2008
please add the serial number of the base dongle
to your order
supports MCS12Z, MCS12X and MCS12
includes software for Windows, Linux and MacOSX
requires Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, Power Debug II or
PowerDebug PRO
supports ARC 700, ARC 600, ARC EM, ARC HS,
ARCtangent-A5 and ARCtangent-A4
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 20 pin connector
supports ARC 700, ARC 600, ARC EM, ARC HS,
ARCtangent-A5 and ARCtangent-A4
please add the base serial number of your debug
cable to your order
supports ARC 700, ARC 600, ARC EM, ARC HS,
ARCtangent-A5 and ARCtangent-A4
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 60 pin XDP connector
Superseded by LA-3750 JTAG Debugger for ARC (ICD)
JTAG Debugger for PWRficient (ICD)
supports PA6T-1682M
supports (1.8V - 5.0V)
Concurrent debugging of both cores in
dual-core chip requires a
License for Multicore Debugging (LA-7960X)
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 16 pin connector
supports AndeCore (0.4 V - 5 V)
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 20 pin connector
supports AndeStar (0.4 V - 5 V)
Extension applicable to the following debug cables
(purchased separately):
for LA-7746 (JTAG Debugger for ARM7)
for LA-7742 (JTAG Debugger for ARM9)
for LA-7744 (JTAG Debugger for ARM10)
for LA-7765 (JTAG Debugger for ARM11)
for LA-7843 (JTAG Debugger for Cortex-A/-R (ARMv7))
for LA-7844 (JTAG Debugger for Cortex-M)
please add the serial number of the base dongle
to your order
supports FREESCALE ColdFire Family
includes software for Windows, Linux and MacOSX
requires Power Debug Module or PowerTrace
debug cable with 26 pin connector
Preprocessor for ColdFire
adaption to standard FREESCALE connector
requires LA-3757 (BDM Debugger for ColdFire HS)
voltage range 3.0V to 5.5V
supports Xtensa Cores from Tensilica
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 14 pin connector
Superseded by LA-3762 JTAG Debugger for Xtensa 20 Pin
supports Xtensa Cores from Tensilica
please add the base serial number of your debug
cable to your order
XTENSA JTAG Adapter to
XTAV60 Target
14 pin to 50 pin
Boards: XTAV60
supports Xtensa Cores from Tensilica
via an ARM JTAG interface
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 20 pin connector
allows to connect LA-3762 to boards designed for LA-3760
Converter for ST20 debug connector
Converts H-UDI14 pins to ST20 20 pins
Converter for SH725x from 14 pin JTAG to
Mictor 38 pin on target (only JTAG)
Converter for SH4 AUD Trace 36 pins of Yamaichi
to JTAG and AUD pins of Mictor
Converter 14 pin and 36 pins of Yamaichi to JTAG
and AUD pins of ERNI (inclusive adapter cables)
For use with ETAS calibration tool
ETMv1 Conv. Mictor-38, 2x MIPI-34 to MIPI-60
ARM Converter to connect an ARM Preprocessor with
one Mictor-38 for 16-bit ETMv1 and two CombiProbes
for two 4-bit system trace ports to a MIPI-60
connector on the target.
Conv. Mictor-38, 2x MIPI-34 to MIPI-60
Converter to connect Preprocessor AUTOFOCUS II Mictor38
and 2 MIPI34 CombiProbes to MIPI60 (QSH) connector
ARM/Cortex: Converter to connect Mictor38 TRACE A (16-bit ETMv3)
and two MIPI34 CombiProbes to MIPI60 (QSH) connector on the
target
x86/x64: Converter to connect Mictor38 TRACE A and a MIPI34
CombiProbes to MIPI60 (QSH) connector on the target
Converter to connect a 20-pin debug cable to 10/20/34 pin
connectors specified by MIPI
ARM Converter MIPI-34 to ARM-20 or TI-14
Converter to connect the CombiProbe to an ARM-20
connector specified by ARM or to a TI-14 connector
specified by Texas Instruments
Converts to debug cable connector
supports Teaklite III interface
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 20 pin connector
supports Teaklite III
please add the serial number of the base debug
cable to your order
HW-Upgrades for debug cables with serial number
below C0808xxxxxxx require a valid
software guarantee or a valid software maintenance key
supports TEAKLITE-III
requires a debug cable with serial number
C0808xxxxxxx or higher
requires a valid software guarantee or a valid
software maintenance key
please add the serial number of the base debug
cable to your order
JTAG Debugger for Intel® x86/x64 (ICD)
Supports Intel® Atom™ cores,
and Intel® Core i3,i5,i7
(32-bit and 64-bit)
Multicore debugging included
includes software for Windows, Linux and MacOSX
requires Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, PowerTrace, Power Debug II
or Power Debug PRO
debug cable with 60-pin XDP connector
Superseded by LA-4590 Package CombiProbe 2 MIPI60-Cv2
JTAG Debugger for Intel x86/x64 Add.
Supports Intel® Atom™ cores and
Intel® Core i3,i5,i7
(32-bit and 64-bit)
Multicore debugging included
please add the serial number of the base debug
cable/CombiProbe/QuadProbe to your order
Only suitable for debug cables newer than 08/2008
supports 78K0R and RL78 cores (16-bit)
includes software for Windows, Linux and MacOSX
requires Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, Power Debug II or
PowerDebug PRO
supports APS3 cores (32-bit)
includes software for Windows, Linux and MacOSX
requires PowerDebug Module
debug cable with 60 pin connector
supports APS3 cores (32-bit)
requires a debug cable with serial number
C0808xxxxxxx or higher
please add the serial number of the base debug
cable to your order
supports AVR32 cores (32-bit)
includes software for Windows, Linux and MacOSX
requires PowerDebug Module
debug cable with 10 pin connector
supports AVR32
please add the serial number of the base debug
cable to your order
Converter to connect a Debug Cable to a TI-14 or
TI-20-Compact connector which is used on many
targets with processors from Texas Instruments.
Converter MIPI-34 to JTAG MIPS14 + IFLOW
Converter MIPI-34 to
14 pin JTAG MIPS and
IFLOW Trace10
includes 10 pin Cable 100 mm
Converter MIPI-34 to TI-20-Compact
Converter to connect the CombiProbe to a connector
specified by Texas Instruments (TI) which is used
on a few targets with TI processors.
Converter MIPI-34 to C166-16
Converter MIPI-34 to
16 pin C166 target adapter
Converter MIPI-34 to MIPI-60
Converter to connect the CombiProbe to a MIPI-60
connector on the target
supports APS3 cores (32-bit)
includes software for Windows, Linux and MacOSX
requires PowerDebug Module
debug cable with 20 pin connector
supports RX600, RX610
derivatives from Renesas
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 14 pin connector
Converter MIPI-34 to SD or Micro SD Socket
Converter to connect the CombiProbe to a SD or Micro
SD card connector in case the signals alternatively
provide debug functionality
Merges up to 4 JTAG interfaces to a daisy-chain
requires that all JTAG interfaces use the same VTREF
includes 4 JTAG Cable 20 Pin (LA-1968)
Converter for RX from 14 pin JTAG to
Mictor 38 pin on target (only JTAG)
Conv. Intel x86/x64 MIPI34 to XDP60
Converter from MIPI34 connector on
CombiProbe for x86/x64 to 60 pin
XDP (Samtec) connector
JTAG for all platforms, 4-bit System Trace only for Medfield
Conv. Intel x86/x64 Multiple Con. to XDP60
Converter from MIPI34 connector on
CombiProbe for Intel x86/x64
+ from XPD60 connector on
JTAG probe for Intel x86/x64
+ from Mictor for STP
to 60 pin XDP (Samtec) connector
Converter for RX AUD Trace,
JTAG14 and Yamaichi 36-pin to Mictor38
supports Beyond Cores (0.4 V - 5 V)
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 20-pin connector
supports QorIQ PowerPC 64-bit
Multicore debugging included
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 16 pin connector
debugger extension for QorIQ PowerPC 64-bit
requires a valid software guaranty or a valid
software maintenance key
only suitable for debug cables newer than 07/2008
please add the serial number of the base debug
cable to your order
supports QorIQ 32-bit with e500mc cores
Multicore debugging included
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 16 pin connector
debugger extension for QorIQ 32-bit with e500mc cores
requires a valid software guaranty or a valid
software maintenance key
only suitable for debug cables newer than 07/2008
please add the serial number of the base debug
cable to your order
supports PowerQuiccIII (MPC85XX) and
QorIQ 32-bit with e500 core
(P10XX, P2010, P2020, BSC9xxx)
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 16 pin connector
Concurrent debugging of two or more cores
in multicore chip requires a
License for Multicore Debugging (LA-7960X)
debugger extension for PowerQuiccIII (MPC85XX) and
QorIQ with e500 core
requires a valid software guaranty or a valid
software maintenance key
only suitable for debug cables newer than 07/2008
please add the serial number of the base debug
cable to your order
supports SMARTi_LU, XC2xxx, XE16x
Onchip Trace and MCDS features through JTAG/DAP
please provide the serial number for LA-7759
together with the order
supports decoding of MCDS-based trace data,
on-chip and off-chip
please add the serial number of the base debug
cable to your order
Preprocessor for ST40 with AUD,
200 MHz clock speed
with 36-pin Yamaichi connector
Requires LA-7985 for 14 pin AUD connector
voltage range 3.0V to 3.6V
Preprocessor for NIOS-II,
150 MHz DDR clock speed,
with MICTOR38 connector
requires PowerTrace
voltage range 1.5V to 5.0V
Converter Mictor 38 to XILINX XGI
Converter Mictor connector to GPIO header
of XILINX ML403/ML501 for
Preprocessor for MicroBlaze (LA-3803)
Preprocessor for Beyond AUTOFOCUS II (LA-3908)
Converter Mictor 38 to S3EStarter/MicroBlaze
Converter Mictor connector to FX2 header
of XILINX Spartan3EStarter for
Preprocessor for MicroBlaze (LA-3803)
Converter Mictor 38 to S3ADSPStarter/MicroBla
Converter Mictor connector to trace header
of XILINX Spartan3ADSP1800Starter for
Preprocessor for MicroBlaze (LA-3803)
JTAG Adapter Spartan3
Xilinx MicroBlaze
16 pin to 6 pin
Boards: EVB Spartan3EStarter Kit; EVB S3ADSP1800A
Converter to connect an ARM Preprocessor
(up to 32-bit ETMv3) and a CombiProbe
(STM/STP) to a MIPI-60 connector on the target.
This converter is designed for L8540 from
ST Ericsson.
Converter to connect an ARM Preprocessor with
MICTOR-38 and a ARM debug cable with JTAG20 to a
20 pin connector specified by MIPI and CoreSight
It allows to use the Preprocessor on the 4 bit wide
trace port of the MIPI-20 connector
It can be re-configured for MIPI-34
U8500 Conv. 2x Mictor38, 3x MIPI34 to MIPI60
Converter to connect an ARM Preprocessor (up to
24-bit PTM/ETMv3) and up to three CombiProbes
(3x STM/STP) to a MIPI-60 connector on the target.
This converter is designed for U8500/U5500
from ST Ericsson.
OMAP4 Conv. 2xMictor, ARM20, MIPI34 to MIPI60
Converter to connect an ARM Preprocessor (up to
18-bit PTM) and one CombiProbe (STM; two connection
options) or a Debug Cable to a MIPI-60 connector on
the target. This converter is designed for
OMAP4xxx based boards from Texas Instruments.
OMAP3 Conv. Mictor-38, MIPI-34 to Mictor-38
Converter to connect an ARM Preprocessor and a
CombiProbe to a Mictor connector on the target.
This converter is designed for the OMAP3503 board
from Spectrum Digital. The upper ETM signals on
the Mictor can alternatively be used for system
trace (SDTI).
ETMv3 Conv. Mictor-38, MIPI-34 to MIPI-60
ARM Converter to connect an ARM Preprocessor with
one Mictor-38 for 16-bit ETMv3 and one CombiProbe
for a 4-bit system trace port to a MIPI-60
connector on the target
Converter 16 Pin JTAG to 10 Pin
Halfe-Size-Connector DAP Interface
for TriCore / XC2000
requires
LA-7759 (OCDS Debugger for XC2000/C166S V2)
or
LA-7756 (OCDS Debugger for TriCore)
Converter to connect an ARM Preprocessor to a
MIPI-60 on the target. Suitable for up to 16-bit
ETMv3. The converter is prepared to support various
other configurations because all clock and data
signals of the MIPI-60 are connected to the
Preprocessor.
Converter to connect a Preprocessor with MIPI-60
connector to a Mictor-38 connector on the target
assuming an ETMv3 pinout up to 16 bit.
Converter to connect Preprocessor AUTOFOCUS II Mictor38
to MIPI60 (QSH) connector
ARM/Cortex: Converter to connect Mictor38 TRACE A
and TRACE B (32-bit ETMv3) and an ARM Debug Cable
to a MIPI60 connector on the target
x86/x64: Converter to connect Mictor38 TRACE A to
to a MIPI60 connector on the target
Converter 16 Pin JTAG to 10 Pin
Half-Size-Connector for BOSCH MEDC17
requires LA-7756 (OCDS Debugger for TriCore)
Converter for Autofocus Trace to
Hirose 36 connector for SHx processors
converter only for
LA-7817 (JTAG Debugger for SH2/SH3/SH4 20 Pin)
to support the ASEBRK signal
110 mm flex extension for Mictor 38-pin connector
Required for SHx to enable the CPU debug mode.
The cable forces target signal MPMD (Mictor pin-3)
to GND
Conv. XDP60-1x20pol-MIPI34
Testadapter from 34pin MIPI to
1 x 20pin 2,54mm post-header to
60 pin XDP Intel x86/x64 (LA-3776)
Conv. XDP60-3x20pol-XDP60
Testadapter from 60 pin XDP to
3 x 20pin 2,54mm post-header to
60 pin XDP for Intel x86/x64 (LA-3776)
Conv. Intel® x86/x64 Debugger to Hirose31
Converter from 60 pin XDP (Samtec) connector on
JTAG Debugger for Intel x86/x64 (LA-3776) to 31 pin
XDP-SSA (Hirose) connector
(not recommended because of poor signal quality)
Conv. Intel® x86/x64 Debugger to ZIF24 pin
Converter from 60 pin XDP (Samtec) connector on
JTAG Debugger for Intel x86/x64 (LA-3776) to 24 pin
XDP-SFF (ZIF) connector
(not recommended because of poor signal quality)
Conv. Intel® x86/x64 Debugger to ZIF26 pin
Converter from 60 pin XDP (Samtec) connector on JTAG
Debugger for Intel x86/x64 (LA-3776) to 26 pin XDP-SFF
(ZIF) connector
(not recommended because of poor signal quality)
Conv. Intel® x86/x64 Debug. to Intel® MIPI34
Converter from 60pin XDP (Samtec) connector on
JTAG Debugger for Intel x86/x64 (LA-3776) to
Intel MIPI34 connector
Converter from JTAG 16 (TriCore pinout of LA-7756)
and Samtec 40 pin -> ERF8 22 pin (Samtec 22 pin)
Includes Samtec 22-pin flex extension
Converter from AUTO26
(TriCore pinout of LA-3737)
and Samtec 40 pin -> ERF8 22 pin (Samtec 22 pin)
for LA-3912 Preproc. TriCore AGBT HF-Flex
and if no separate JTAG/AUTO connector is available
on the target for
LA-2707 (Debugger for TriCore Automotive PRO)
LA-3737 (JTAG Debugger for TriCore Automotive)
LA-7756 (OCDS Debugger for TriCore)
Conv. Samtec40/COP16 to Samtec70 PowerOrg
Converter from JTAG 16 (PPC-COP pinout of LA-3794/LA-3795)
and Samtec 40 pin to Power.org 70 pin
for LA-7987 Preproc. QorIQ PowerPC HSTP HF-Flex
Conv. Samtec40/COP16 to Samtec46 PowerOrg
Converter from JTAG 16 (PPC-COP pinout of LA-3794/LA-3795)
and Samtec 40 pin to Power.org 46 pin
for LA-7987 Preproc. QorIQ PowerPC HSTP HF-Flex
Conv. Samtec40/COP16 to Samtec22 PowerOrg
Converter from JTAG 16 (PPC-COP pinout of LA-3794/LA-3795)
and Samtec 40 pin to Power.org 22 pin
for LA-7987 Preproc. QorIQ PowerPC HSTP HF-Flex
Converter from JTAG 20 (ARM pinout) and Samtec 40 pin
to Samtec 40 pin
for LA-7988 Preproc. ARM HSSTP HF-Flex
Converter from Mictor38 of RTP port of TI chips to
Mictor38 of the ETM trace port plus JTAG 20 pin
Conv. Samtec40 HSSTP to SATA
Converter from Samtec 40 pin
to SATA 7pin
for LA-3910 Preproc. PPC4xx HSTP HF-Flex
for LA-7987 Preproc. QorIQ PowerPC HSTP HF-Flex
1 flex extension SATA cable 500 mm included
Converter to connect an ARM Preprocessor with
MICTOR-38 and a ARM debug cable with JTAG20 to a
34 pin connector specified by MIPI and CoreSight
It allows to use the Preprocessor on the 4 bit wide
trace port of the MIPI-34 connector
It can be re-configured for MIPI-20
Converter 26-pin Automotive Debug Cable
to 10-pin JTAG half-size (Automotive, ECU14)
for
LA-2707 (Debugger for TriCore Automotive PRO)
LA-2708 (Debugger for MPC5xxx Automotive PRO)
LA-2709 (Debugger for RH850/V850 Automotive PRO)
LA-2713 (Debug-Bundle MPC5xxx/TriCore Automotive PRO)
LA-2714 (Debug-Bundle TriCore/RH850 Automotive PRO)
LA-3736 (JTAG Debugger for MPC5xxx Automotive)
LA-3737 (JTAG Debugger for TriCore Automotive)
LA-3738 (Debugger-Bundle MPC5xxx/TriCore Automotive)
LA-3739 (Debugger for RH850/V850 Automotive)
LA-3753 (Debugger-Bundle TriCore/RH850 Automotive)
Converter 14-pin OnCE-PPC to
10-pin JTAG half-size (Automotive, ECU14)
for LA-7753 (JTAG Debugger for MPC55xx/MPC56xx)
Converter 16-pin TriCore to
10-pin JTAG half-size (Automotive, ECU14)
also supporting DAP (2-wire)
for LA-7756 (OCDS Debugger for TriCore)
JTAG Debugger for TeakLite-4 (ICD)
supports Teaklite-4 interface
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 20 pin connector
JTAG Debugger for TeakLite-4 Add. (ICD)
supports Teaklite-4
includes software for WINDOWS, HLL debugger
Extension applicable to the following debug cables
with serial number C0808xxxxxxx or higher
please add the serial number of the base debug
cable to your order
JTAG Debugger Extension for TEAKLITE-4
supports TEAKLITE-4
requires a debug cable with serial number
C0808xxxxxxx or higher
requires a valid software guarantee or a valid
software license key
please add the serial number of the base debug
cable to your order
Converter from SAMTEC60 + JTAG14 to MICTOR38 for
MIPS
Converter to connect an ARM Preprocessor (16-bit PTM)
to the OMAP5432 EVM (successor of the PandaBoard).
Converter 16-pin JTAG (TriCore)
to 26-pin Automotive Debug Cable
also supporting DAP (2-wire)
for LA-7756 (OCDS Debugger for TriCore)
Converter 26-pin Automotive Debug Cable
to 16-pin JTAG (TriCore)
also supporting DAP (2-wire)
for
LA-2707 (Debugger for TriCore Automotive PRO)
LA-3737 (JTAG Debugger for TriCore Automotive)
Converter for
SPC560B54/B60/B64 (Bolero)
adaptation from
ET176-QF67 to BGA208 with additional Mictor38 NEXUS
debug connector
requires
TO-1325 (Emul. Adapter for T0-socket ET176-QF67)
Converter for
- SPC560B40/B44/B50/C40/C44/C50 (Bolero)
adaptation from
ET100-QF49 to BGA208 with additional Mictor38 NEXUS
debug connector
requires
TO-1250 (Emul. Adapter for T0 socket ET100-QF49)
Converter for MPC5646Cxxx (Bolero3M)
adaptation from
ET176-QF67 to BGA256 with additional Mictor38 NEXUS
debug connector
requires
TO-1325 (Emul. Adapter for T0-socket ET176-QF67)
Converter for SPC56ECxx (Bolero3M)
adaptation from
ET176-QF67 to BGA256 with additional Mictor38 NEXUS
debug connector
requires
TO-1325 (Emul. Adapter for T0-socket ET176-QF67)
Converter for
MPC5605B/6B/7B
adaptation from
ET176-QF67 to BGA208 with additional Mictor38 NEXUS
debug connector
requires
TO-1325 (Emul. Adapter for T0-socket ET176-QF67)
Converter for
- MPC5602B/3B/4B/2C/3C/4C (Bolero)
adaptation from
ET144-QF63 to BGA208 with additional Mictor38 NEXUS
debug connector
requires
TO-1310 (Emul. Adapter for T0 socket ET144-QF63)
Converter for
- MPC5602B/3B/4B/2C/3C/4C (Bolero)
adaptation from
ET100-QF49 to BGA208 with additional Mictor38 NEXUS
debug connector
requires
TO-1250 (Emul. Adapter for T0 socket ET100-QF49)
Converter to connect a ARM Debug Cable
to a 16 pin PowerPC connector (PPC4xx)
Converter MIPI-34 to Intel FPC-41
Converter from MIPI34 connector on
CombiProbe for Intel x86/x64 to FPC 41pin
(Panasonic) connector
Adapter for the Intel Medfield Smartphone
Reference Platform
ARM Conv. ARM-20, MIPI-34 to Mictor-38
Converter to connect the ARM Debug Cable or
the CombiProbe to a Mictor connector on the
target. This is needed if you want to debug
without a Preprocessor and if there is only
a Mictor connector on the target.
The trace signals of the CombiProbe are
connected to the lowest four trace signals of
the Mictor (ETMv3 pinout, continuous mode).
But tracing is normally no use case due to
the bandwidth limitations of the CombiProbe.
Converter from ARM 20-pin connector to
Altera 10-pin (Byteblaster) connector or
RISC-V 10-pin
Target connector pitch can be
2.54mm or 1.27mm (half size).
Converter ARM-20 to UBI32-10
Converter 20 pin JTAG ARM to
UBI32-10
Converter 20 pin JTAG ARM to
78K 16 pin NEC
Converter 20 pin JTAG ARM to
RL78 14 pin Renesas
Conv. XDP60 to MIPI60 (Intel)
Converter from XDP 60 pin
to MIPI 60 pin on target
for ITP 60 pin to MIPI 60 pin (Intel)
Connector for Intel MIPI 60 on target to
- CombiProbe Intel x86/x64 MIPI60-C
- Prepro. for Intel® PT AUTOFOCUS MIPI60-P
Converter from JTAG14 of
LA-7753 (JTAG Debugger Qorivva MPC5xxx/SPC5xxx)
and from AUTO26 of
LA-2708 (Debugger for MPC5xxx Automotive PRO)
LA-3736 (JTAG Debugger for MPC5xxx Automotive)
and Samtec 40 pin of
LA-3911 (Preprocessor Aurora NEXUS Automotive)
to Samtec ERF 34-pin Power.ORG pinout
Includes Samtec 34-pin flex extension
Converter from JTAG14 of
LA-7753 (JTAG Debugger Qorivva MPC5xxx/SPC5xxx)
and from AUTO26 of
LA-2708 (Debugger for MPC5xxx Automotive PRO)
LA-3736 (JTAG Debugger for MPC5xxx Automotive)
and Samtec 40 pin of
LA-3911 (Preprocessor Aurora NEXUS Automotive)
to Samtec ERF 22-pin Power.ORG pinout
Includes Samtec 22-pin flex extension
for LA-3911 Preproc. Aurora NEXUS
and if no separate JTAG/AUTO connector is available
on the target, for
LA-7753 (JTAG Debugger Qorivva MPC5xxx/SPC5xxx)
Converter from Automotive Debug Cable (26-pin)
to 14 Pin JTAG/OnCE header on target
for
LA-2708 (Debugger for MPC5xxx Automotive PRO)
LA-3736 (JTAG Debugger for MPC5xxx Automotive)
Converter from Automotive Debug Cable (26-pin)
to Mictor 38pin (NEXUS MPC5XXX pinout)
for
LA-2708 (Debugger for MPC5xxx Automotive PRO)
LA-3736 (JTAG Debugger for MPC5xxx Automotive)
Converter from Automotive Debug Cable (26-pin)
to Samtec 50pin (NEXUS MPC5XXX pinout)
for
LA-2708 (Debugger for MPC5xxx Automotive PRO)
LA-3736 (JTAG Debugger for MPC5xxx Automotive)
Converter from 14 Pin JTAG/OnCE MPC5XXX to AUTO26/20/10
use with
LA-7753 JTAG Debugger Qorivva MPC5xxx/SPC5xxx (ICD)
to connect to targets designed for
LA-2708 (Debugger for MPC5xxx Automotive PRO)
LA-3736 (JTAG Debugger for MPC5xxx Automotive)
Conv. Intel® x86/x64 Debuger to MIPI34 Galil
Converter from 60pin XDP (Samtec) connector on
JTAG Debugger for Intel x86/x64 (LA-3776) to 34pin
MIPI connector Galileo/Quark
Converter from MIPI60-Q or MIPI60-Cv2 pin-out to XDP 60 pin-out
Converter to connect an ARM ETM MIPI Preprocessor
with MIPI-60 connector and an ARM Debug Cable to
two Mictor-38 connectors (32-bit ETMv3)
on the target
Converter to connect an ARM Debug Cable to a 14-pin
JTAG connector found on Xilinx target boards
Converter Mictor38 ARM20 MIPI34 UART with SMDswitch
to SD or Micro SD Socket
Converter Mictor38 ARM20 MIPI34 UART
to SD or Micro SD Socket
Converter from Mictor76 to Mictor38 for
LA-3909 (Preprocessor for RH850/V850 Flex Cable)
Conv. ARM-20 to Digilent PMOD™
Converter to connect a ARM Debug Cable
to a standard 6-pin "Pmod™" connector
“Pmod™” is a trademark of Digilent Inc.
Conv. MIPI60/JTAG20 to 60 Pin CTOOLS
Converter MIPI60/20 Pin JTAG (ARM and TI)
to 60 Pin CTOOLS connector on target
DAP Converter 26-pin Automotive Debug Cable/16-pin Standard Cable
(TriCore) to CAN Physical Layer
In conjunction with
LA-2707 (Debugger for TriCore Automotive PRO)
LA-3737 (JTAG Debugger for TriCore Automotive)
LA-7756 (JTAG Debugger for TriCore Standard)
Converter from Beyond (20-pin) to NXP/Jennic (10-pin)
LA-3793 (JTAG Debugger for Beyond)
Connector for Intel MIPI60 Converged on target to
- Whisker MIPI60-Q for Quad-Probe x86/x64
- Prepro. for Intel® PT AUTOFOCUS MIPI60-P
Connector for Intel MIPI60 Converged on target to
- Whisker MIPI60-Cv2 for CombiProbe
- Prepro. for Intel® PT AUTOFOCUS MIPI60-P
Converter to connect a Debug Cable to 10/20/34 pin
connectors specified by MIPI.
Debug Converter for MinnowBoard
Converter to connect
LA-3776 JTAG Debugger for Intel® x86/x64 (Intel XDP60)
or
LA-4512/LA-4516 CombiProbe Intel® x86/x64 MIPI60-C
to the MinnowBoard MAX LA-3894
Converter to connect a RH850 HSTP Aurora Preprocessor to the
Renesas Evalboard: RH850-CCC-404PIN-PB-T1-V1
SABRE-AI to TRACE32 ADAPTER BOARD
Convert Mictor38 to SABRE-AI Target Board
Program flow trace for PPC4xx
1.2 GHz clock speed
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Supports 1.2 to 3.3V - else contact support
Requires PowerTrace
(PowerTrace Ethernet Version 6 or higher)
voltage range 1.2V to 3.3V
Supports off-chip trace port for PPC4XX if
applied to an AUTOFOCUS II preprocessor
Requires
LA-7986 Mictor38-Mictor38-JTAG 16pin Conv. for PPC4XX
please add the serial number of the preprocessor to
your order
AUTOFOCUS II Preprocessors with serial number
C0806xxxxxx and lower have to be send to Lauterbach
Germany for an hardware upgrade
Preproc. for MICROBLAZE AUTOFOCUS II Flex
Preprocessor for Real-Time Trace of MICROBLAZE
Requires Xilinx Vivado 2018.3 or later or Vivado 2018.2
with special patch from Xilinx (see
https://www.xilinx.com/support/answers/71422.html#).
250 MHz clock speed
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Supports 1.2 to 3.3V - else contact support
Requires PowerTrace Version 6 or higher
or PowerTrace II
voltage range 1.2V to 3.3V
Trace License for MicroBlaze AUTOFOCUS II
Supports off-chip trace port for MicroBlaze if
applied to an AUTOFOCUS II preprocessor
Requires
LA-7986 Mictor38-Mictor38-JTAG 16pin Conv. for PPC4XX
Requires Xilinx Vivado 2018.3 or later or Vivado 2018.2
with special patch from Xilinx (see
https://www.xilinx.com/support/answers/71422.html#).
please add the serial number of the preprocessor to
your order
AUTOFOCUS II Preprocessors with serial number
C0806xxxxxx and lower have to be send to Lauterbach
Germany for an hardware upgrade
Preprocessor for AUD Real-Time Trace for SH2A,
SH4 and SH4A cores
550 MHz clock speed
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Supports 1.2 to 3.3V - else contact support
Requires PowerTrace
(PowerTrace Ethernet Version 6 or higher)
Requires converter LA-7819 for 14 pin debug cables
voltage range 1.2V to 3.3V
Supports AUD off-chip trace port for SH2A, SH4,
SH4A if applied to an AUTOFOCUS II preprocessor
please add the serial number of the preprocessor to
your order
AUTOFOCUS II Preprocessors with serial number
C0806xxxxxx and lower have to be send to Lauterbach
Germany for an hardware upgrade
Preproc. for C6000 DSP AUTOFOCUS II Flex
Preprocessor for Real-Time Trace of C64x+
330 MHz trace clock
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Supports 1.2 to 3.3V - else contact support
Requires PowerTrace Version 6 or higher
or PowerTrace II
voltage range 1.2V to 3.3V
Trace License for C6000 in AUTOFOCUS II
Supports off-chip trace port for C64x+ if
applied to an AUTOFOCUS II preprocessor
please add the serial number of the preprocessor to
your order
AUTOFOCUS II Preprocessors with serial number
C0806xxxxxx and lower have to be send to Lauterbach
Germany for an hardware upgrade
Preproc. for TEAKLITE-III AUTOFOCUS II Flex
Preprocessor for Real-Time Trace of TEAKLITE-III
500 MHz clock speed
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Supports 1.2 to 3.3V - else contact support
Requires PowerTrace
(PowerTrace Ethernet Version 6 or higher)
voltage range 1.2V to 3.3V
Trace License for TEAKLITE-III AUTOFOCUS II
Supports off-chip trace port for TEAKLITE-III if
applied to an AUTOFOCUS II preprocessor
please add the serial number of the preprocessor to
your order
AUTOFOCUS II Preprocessors with serial number
C0806xxxxxx and lower have to be send to Lauterbach
Germany for an hardware upgrade
Preprocessor for RAM Trace Port on TI chips
500 MHz clock speed
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Supports 1.2 to 3.3V - else contact support
Requires PowerTrace
(PowerTrace Ethernet Version 6 or higher)
May require
LA-3835 Conv. Mictor38/RTP to Mictor38/ETM+JTAG20
voltage range 1.2V to 3.3V
Supports off-chip RAM trace port for of TI chips if
applied to an AUTOFOCUS II preprocessor
please add the serial number of the preprocessor to
your order
AUTOFOCUS II Preprocessors with serial number
C0806xxxxxx and lower have to be send to Lauterbach
Germany for an hardware upgrade
May require
LA-3835 Conv. Mictor38/RTP to Mictor38/ETM+JTAG20
Preprocessor for Real-Time Trace of MIPS32
EJTAG 2.6 derivatives or higher
600 MBaud (300MHz clock speed, DDR)
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Supports 1.2 to 3.3V - otherwise contact support
Requires PowerTrace
(PowerTrace Ethernet Version 6 or higher)
voltage range 1.2V to 3.3V
Preprocessor for Intel® Processor Trace
600 MBaud (300MHz clock speed, DDR)
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Supports 1.2 to 3.3V - otherwise contact support
Requires PowerTrace II
voltage range 1.2V to 3.3V
Allows to decode Intel Processor Trace recorded to
SDRAM or PowerTrace II
please add the serial number of the preprocessor to
your order
AUTOFOCUS II Preprocessors with serial number
C0806xxxxxx and lower have to be send to Lauterbach
Germany for an hardware upgrade
Preprocessor for Beyond BA2x cores
Instruction trace only
600 MBaud (300MHz clock speed, DDR)
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Supports 1.8 to 3.3V - otherwise contact support
Requires PowerTrace
(PowerTrace Ethernet Version 6 or higher)
May require
LA-3804 Converter Mictor 38 to XILINX XGI
voltage range 1.2V to 3.3V
Preprocessor for RH850 and V850 with
parallel Nexus trace interface
Voltage range:
1..5 V
TRACE port:
2..16 MDO (data) lines
1..2 MSEO (control) lines
Data Bandwidth:
up to 200 MBit/s
Connector:
76 pin mictor connector
requires PowerTrace II
Superseded by LA-3918 Preprocessor for RH850 AutoFocus II
Preproc. PPC4xx HSTP HF-Flex
Preprocessor for PPC4xx high speed trace port
(Aurora based)
up to 4 lanes,
up to 6.5 Gbit/s per lane
Requires PowerTrace II
Converters for Samtec22/46/70 have to be
ordered separately
voltage range 0.15V to 1.25V
Aurora NEXUS Preprocessor for Qorivva MPC57xx/SPC57XX
(high-speed serial trace port)
- supports reference clock output up to 3125MHz
POWER TRACE II: full support
Supported speeds per lane:
4 lanes @ 4.25Gbps
3 lanes @ 6.0Gbps
2 lanes @ 6.25Gbps
1 lane @ 6.25Gbps
POWER TRACE ETHERNET or POWER TRACE PX limited support
Supported speeds per lane:
4 lanes @ 1.25 GBPS
2 lanes @ 2.5 GBPS
- POWER TRACE ETHERNET module must have serial number
E04xxxxxxxx or higher
Required converter:
- Samtec34 on target requires LA-3871:
Converter Samtec40 HSTP+AUTO26+JTAG14 to Samtec34
including Samtec 34-pin flex extension cable
- Samtec22 on target requires LA-3872:
Converter Samtec40 HSTP+AUTO26+JTAG14 to Samtec22
including Samtec 22-pin flex extension cable
voltage range 0.15V to 1.25V
Supports Qorivva MPC57xx/SPC57XX Aurora NEXUS
(high-speed trace port)
please add the serial number of the preprocessor to
your order
Preprocessor for TriCore Aurora Giga-Bit Trace
(Aurora high-speed trace)
POWER TRACE II: full support
Supported speeds per lane:
4 lanes @ 4.25Gbps
3 lanes @ 6.0Gbps
2 lanes @ 6.25Gbps
1 lane @ 6.25Gbps
POWER TRACE ETHERNET or POWER TRACE PX limited support
Supported speeds per lane:
4 lanes @ 1.25 GBPS
2 lanes @ 2.5 GBPS
- POWER TRACE ETHERNET module must have serial number
E04xxxxxxxx or higher
voltage range 0.15V to 1.25V
Supports decoding of MCDS-based trace data,
on-chip and off-chip
Requires
LA-3829 Conv. Samtec40 to Samtec22 TriCore AGBT
please add the serial number of the preprocessor to
your order
Preproc. for ARC/AUTOFOCUS II 600 Flex
Preprocessor for ARC Real-Time Trace (ARC RTT)
Connector cable and software,
600 MHz clock speed,
8,16,32 Bit Trace Port width,
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Supports 1.2 to 3.3V - else contact support
Requires PowerTrace/Ethernet Version 6 or higher
or PowerTrace II
Trace License for ARC AUTOFOCUS II
Supported for ARC Real-Time Trace (ARC RTT)
if applied to an AUTOFOCUS II preprocessor
please add the serial number of the preprocessor to
your order
AUTOFOCUS II Preprocessors with serial number
C0806xxxxxx and lower have to be send to Lauterbach
Germany for an hardware upgrade
Support for Nexus Onchip Trace (ARC RTT)
(Not required for "Small Onchip Trace" (SmaRT))
please add the base serial number of your debug
cable to your order
Preproc. for C6000 AUTOFOCUS II MIPI60
Preprocessor for Real-Time Trace of C64x+
330 MHz trace clock
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Supports 1.2 to 3.3V - else contact support
Requires PowerTrace Version 6 or higher
or PowerTrace II
voltage range 1.2V to 3.3V
Trace License for C6000 AUTOFOCUS MIPI
Supported for Real-Time Trace of C64x+
if applied to an AUTOFOCUS MIPI preprocessors
please add the serial number of the preprocessor to
your order
voltage range 1.2V to 3.3V
Trace License for Nios II AUTOFOCUS II
Supports off-chip trace port for Nios II if
applied to an AUTOFOCUS II preprocessor
please add the serial number of the preprocessor to
your order
AUTOFOCUS II Preprocessors with serial number
C0806xxxxxx and lower have to be send to Lauterbach
Germany for an hardware upgrade
Preprocessor for RH850 parallel Nexus trace interface
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Voltage range: 1.2 to 3.3V
Trace port: 2..16 MDO (data), 1..2 MESO (control)
Bandwidth: 600 MBaud (300MHz clock speed, DDR)
Connector: 38 pin mictor connector
requires PowerTrace II
Supports RH850 parallel Nexus tracing
please add the serial number of the preprocessor to
your order
AUTOFOCUS II Preprocessors with serial number
C0806xxxxxx and lower have to be send to Lauterbach
Germany for an hardware upgrade
Preproc. for ARC/AUTOFOCUS 600 MIPI
Preprocessor for ARC Real-Time Trace (ARC RTT)
Connector cable and software,
600 MHz clock speed,
8,16,32 Bit Trace Port width,
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
SAMTEC60 MIPI connector,
Supports 1.2 to 3.3V - else contact support
Requires PowerTrace/Ethernet Version 6 or higher
or PowerTrace II
Preproc. for STRED AUTOFOCUS II
Preprocessor for Real-Time Trace of STRED
330 MHz trace clock
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Supports 1.2 to 3.3V - else contact support
Requires PowerTrace Version 6 or higher
or PowerTrace II
Trace License for STRED AUTOFOCUS II
Supported for STRED Trace
if applied to an AUTOFOCUS II preprocessor
please add the serial number of the preprocessor to
your order
AUTOFOCUS II Preprocessors with serial number
C0806xxxxxx and lower have to be send to Lauterbach
Germany for an hardware upgrade
Preproc. for C7000 DSP AUTOFOCUS II Flex
Preprocessor for C7000 Trace
330 MHz trace clock
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Supports 1.2 to 3.3V - else contact support
Requires PowerTrace Version 6 or higher
or PowerTrace II
Trace License for C7000 in AUTOFOCUS II
Supports C7000 trace
applied to an AUTOFOCUS II preprocessor
please add the serial number of the preprocessor to
your order
AUTOFOCUS II Preprocessors with serial number
C0806xxxxxx and lower have to be send to Lauterbach
Germany for an hardware upgrade
Preproc. for C7000 AUTOFOCUS II MIPI60
Preprocessor for Real-Time Trace of C7000
330 MHz trace clock
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Supports 1.2 to 3.3V - else contact support
Requires PowerTrace Version 6 or higher
or PowerTrace II
Trace License for C7000 AUTOFOCUS MIPI
Supports C7000 trace
if applied to an AUTOFOCUS MIPI preprocessors
please add the serial number of the preprocessor to
your order
AUTOFOCUS II Preprocessors with serial number
C0806xxxxxx and lower have to be send to Lauterbach
Germany for an hardware upgrade
Preproc. for C6000 DSP HSSTP HF-Flex
Serial preprocessor for C6000 with HSSTP
Connector cable and software
Supported maximum speed per lane:
4 lanes @ 5.00Gbps
3 lanes @ 6.25Gbps
2 lanes @ 6.25Gbps
1 lane @ 6.25Gbps
Requires PowerTrace II
voltage range 0.15V to 1.2V
Trace License for C6000 in HSSTP
Supports off-chip trace port for C64x+ if
applied to HSSTP preprocessor
please add the serial number of the preprocessor to
your order
AUTOFOCUS II Preprocessors with serial number
C0806xxxxxx and lower have to be send to Lauterbach
Germany for an hardware upgrade
Preproc. for RISC-V AUTOFOCUS II
Preprocessor for Trace RISC-V
tested for SiFive Nexus IP
tested for UltraSoc Trace Encoder IP
other IP on request
330 MHz trace clock
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Supports 1.2 to 3.3V - else contact support
Requires PowerTrace Version 6 or higher
or PowerTrace II
Trace License for RISC-V AUTOFOCUS II
Supported for RISC-V
if applied to an AUTOFOCUS II preprocessor
tested for SiFive Nexus IP
tested for UltraSoc Trace Encoder IP
other IP on request
please add the serial number of the preprocessor to
your order
AUTOFOCUS II Preprocessors with serial number
C0806xxxxxx and lower have to be send to Lauterbach
Germany for an hardware upgrade
State-Timing Analyzer, 102 channels,
200 (400) MHz state, 500 MHz timing,
transient recording,
64 MFrames, 48-bit time-stamp,
trigger, filter, trigger Delay, etc.
requires PowerDebug II Ethernet or PowerDebug PRO
State-Timing Analyzer, 102 channels,
200 (400) MHz state, 500 MHz timing,
transient recording,
128 MFrames, 48-bit time-stamp,
trigger, filter, trigger Delay, etc.
requires PowerDebug II Ethernet or PowerDebug PRO
State-Timing Analyzer, 102 channels,
200 (400) MHz state, 500 MHz timing,
transient recording,
256 MFrames, 48-bit time-stamp,
trigger, filter, trigger Delay, etc.
requires PowerDebug II Ethernet or PowerDebug PRO
Preprocessor for RH850 with
serial Nexus trace interface
including Samtec 40-pin flex extension cable
requires PowerTrace II
Supported speeds per lane:
4 lanes at 4.25Gbps
3 lanes at 6.0Gbps
2 lanes at 6.25Gbps
1 lane at 6.25Gbps
LA-3560 PowerTrace Serial 4 GigaByte RH850
Supports 8 lanes at 12.5Gbps
voltage range 0.15V to 1.25V
Superseded by LA-3560 PowerTrace Serial 4 GigaByte RH850
Supports RH850 Aurora NEXUS
(high-speed trace port)
requires serial preprocessor hardware newer than 08/12
(serial number >= C12080164145)
please add the serial number of the serial preprocessor to
your order
Soft Touch normal-size Probe
for Mictor Probe Differential (LA-7947)
includes a retention module and a connector block
Agilent -> normal size
Soft Touch normal-size Probe with cable
for Mictor Probe Differential (LA-7947)
includes a retention module and a connector block
Agilent -> normal size
Soft Touch normal-size Probe
for Mictor Probe (LA-7944)
includes a retention module and a connector block
Agilent -> normal size
Soft Touch normal-size Probe with cable
for Mictor Probe (LA-7944)
includes a retention module and a connector block
Agilent -> normal size
Soft Touch half-size Probe
for Mictor Probe Differential (LA-7947)
includes a retention module and a connector block
Tektronix -> half size
Soft Touch half-size Probe with cable
for Mictor Probe Differential (LA-7947)
includes a retention module and a connector block
Tektronix -> half size
Soft Touch half-size Probe
for Mictor Probe (LA-7944)
includes a retention module and a connector block
Tektronix -> half size
Soft Touch half-size Probe with cable
for Mictor Probe (LA-7944)
includes a retention module and a connector block
Tektronix -> half size
Trace Lic. for Intel® Processor Trace (COB)
Allows to decode Intel Processor Trace recorded to
SDRAM, TRACE32 CombiProbe or
recorded by TRACE32 PowerTrace II+AutoFocus II preprocessor
configuration that does not include LA-3907
please add the serial number of the base debug
cable or CombiProbe to your order
USB-C Breakout Module (Type-C Port)
Cable USB-C to USB-C Breakout Module
Package CombiProbe Type-C (Type-C Port)
CombiProbe ARM-Debugger and 4-Bit Trace
Debug cable and 128-MByte of trace memory
Supports Standard-JTAG, cJTAG and
Serial Wire Debug Port
Bandwidth of 200 MBit/s per trace channel
requires at least one of the following A-licenses:
LA-7742A (JTAG Debugger License for ARM9 Add.)
LA-7746A (JTAG Debugger License for ARM7 Add.)
LA-7765A (JTAG Debugger License for ARM11 Add.)
LA-7843A (JTAG Debugger License for CORTEX-A Add.)
LA-7844A (JTAG Debugger License for CORTEX-M Add.)
Trace support (up to 4-bit) included:
- MIPI System Trace
- ITM via Serial Wire Output/TPIU
- ETM Cortex-M continuous mode via TPIU
Supports the following trace licenses:
LA-7970X (Trace License for the ARM Architecture)
requires Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, PowerTrace, Power Debug II
or Power Debug PRO
5V tolerant inputs; max. output level 3.3V
Superseded by LA-4597 Package for CombiProbe 2 ARM
Package for CombiProbe ARM
Debug cable and 128-MByte of trace memory
Supports Standard-JTAG, cJTAG and
Serial Wire Debug Port
Bandwidth of 400 MBit/s per trace channel
requires at least one of the following A-licenses:
LA-7742A (JTAG Debugger License for ARM9 Add.)
LA-7746A (JTAG Debugger License for ARM7 Add.)
LA-7765A (JTAG Debugger License for ARM11 Add.)
LA-7843A (JTAG Debugger License for CORTEX-A Add.)
LA-7844A (JTAG Debugger License for CORTEX-M Add.)
Trace support (up to 4-bit) included:
- MIPI System Trace
- ITM via Serial Wire Output/TPIU
- ETM Cortex-M continuous mode via TPIU
Supports the following trace licenses:
LA-7970X (Trace License for the ARM Architecture)
requires Power Debug Interface USB 3.0,
Power Debug II or Power Debug PRO
5V tolerant inputs; max. output level 3.3V
Consists of
LA-4570 CombiProbe Hardware
LA-4513 Whisker MIPI20T-HS CombiProbe/uTrace Arm
LA-2109 Half-Size-Cable 20-20 short
LA-2108 Half-Size-Cable 20-10 short
LA-2730 ARM Converter MIPI-20T to ARM-20
LA-4505 Whisker Cable MIPI34 for CombiProbe
LA-1937 MIPI-Half-Size-Cable 34-10
LA-1938 MIPI-Half-Size-Cable 34-20
LA-1939 MIPI-Half-Size-Cable 34
LA-3771 ARM Converter MIPI-34 to ARM-20 or TI-14
Superseded by LA-4597 Package for CombiProbe 2 ARM
CombiProbe MIPS32-Debugger and 4-Bit IFLOW
Debug cable and 128-MByte of trace memory
requires the following A-license:
LA-7760A (JTAG Debugger for MIPS32)
4-Bit IFlow program trace requires:
LA-7971X (Trace License for the MIPS32)
requires Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, PowerTrace, Power Debug II
or Power Debug PRO
5V tolerant inputs; max. output level 3.3V
CombiProbe C166V2-Debugger and 4-Bit Trace
supports C166 V2
Debug cable and 128-MByte of trace memory
requires the following A-license:
LA-7759A (OCDS Debugger for C166S V2)
optional
LA-7789A (JTAG Debugger for OAK/Teaklite-SEIB Add.)
MCDS program flow trace requires:
LA-7975X (Off-Chip Trace for MCDS of C166S-V2)
requires Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, PowerTrace, Power Debug II
or Power Debug PRO
5V tolerant inputs; max. output level 3.3V
Conv. CombiProbe/uTrace to PI-Analog Probe
Converter CombiProbe/uTrace to
LA-7949 Analog Probe for PowerIntegrator
CombiProbe Intel x86/x64 MIPI34
Debug cable and 128-MByte of trace memory
for Intel x86/x64 processors with PTI/STP only
Since the CombiProbe Intel x86/x64 MIPI34 Whisker cable
does not have a serial termination, please contact our
technical support if you want to add a license for another
processor architecture
requires the following A-license:
LA-3776A (JTAG Debugger for Intel x86/x64)
requires Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, PowerTrace, Power Debug II
or Power Debug PRO
5V tolerant inputs; max. output level 3.3V
Superseded by LA-4590 Package CombiProbe 2 MIPI60-Cv2
Whisker for CombiProbe Intel x86/x64 MIPI34
Whisker Cable for CombiProbe MIPI34 for Intel x86/x64
Upgrade to Whisker MIPI20T-HS
Upgrade to Whisker Cable MIPI20T/MIPI10
for CombiProbe/uTrace
Your old Whisker Cable MIPI34 must be returned on
receipt of the replacement Whisker Cable MIPI20T-HS
DCI OOB cable for CombiProbe
supports DCI OOB via USB
Supports 5-pin standard JTAG, cJTAG and
Serial Wire Debug Port for Arm Cortex-M cores
Bandwidth of 200 MBit/s per trace channel
includes 256-MByte of trace RAM to support:
- ITM via Serial Wire Output/TPIU
- ETM Cortex-M continuous mode via TPIU (4-bit)
Trace Streaming up to 100 MByte/s requires
USB 3.0 (SuperSpeed) capable host computer
Concurrent debugging of two or more
Cortex-M cores requires a
License for Multicore Debugging (LA-7960X)
Superseded by LA-4532 Package for uTrace for Cortex-M
Supports 5-pin standard JTAG, cJTAG and
Serial Wire Debug Port for Arm Cortex-M cores
Bandwidth of 400 MBit/s per trace channel
includes 256-MByte of trace RAM to support:
- ITM via Serial Wire Output/TPIU
- ETM Cortex-M continuous mode via TPIU (4-bit)
Trace Streaming up to 100 MByte/s requires
USB 3.0 (SuperSpeed) capable host computer
Concurrent debugging of two or more
Cortex-M cores requires a
License for Multicore Debugging (LA-7960X)
Consists of
LA-4533 uTrace for Cortex-M Hardware
LA-4513 Whisker MIPI20T-HS CombiProbe/uTrace Arm
LA-2109 Half-Size-Cable 20-20 short
LA-2108 Half-Size-Cable 20-10 short
LA-1952 Wall Mount Power Supply
LA-1942 USB-2 Cable
LA-1943 USB-3 Cable
LA-2730 ARM Converter MIPI-20T to ARM-20
Debug cable and 128-MByte of trace memory
support DAP Streaming up to 150 MHz
for the following TC23x, TC26x, TC29x
Aurix ED devices
26-pin Automotive Connector
requires the following A-license:
LA-7756A (Debugger for TriCore Standard Additional)
trace analysis and display requires
LA-3799X (Trace License for TriCore ED)
requires Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, PowerTrace, PowerDebug Pro
or Power Debug II
5V tolerant inputs; max. output level 3.3V
Consists of
LA-4570 CombiProbe Hardware
LA-1947 Automotive HALF-SIZE-CABLE 26-10
LA-1948 Automotive HALF-SIZE-CABLE 26-20
LA-1949 Automotive HALF-SIZE-CABLE 26-26
Superseded by LA-4552 Package for CombiProbe 2 TriCore DAP
Debug cable and 512-MByte of trace memory
support for DAP Streaming
Supports
- DAP (DAP2, DAP3, DAPWide, DAP4): up to 160 MHz,
3.3 V or 5.0 V
- JTAG: 1.8-5.0 V, up to 60 MHz
- DXCPL
DAP streaming requires a DAP mode. For performance reasons,
we recommend DAPWide at 160 MHz.
26-pin Automotive Connector
requires the following A-license:
LA-7756A (Debugger for TriCore Standard Additional)
trace analysis and display requires
LA-3799X (Trace License for TriCore ED)
requires Power Debug Interface USB 3.0,
Power Debug II or PowerDebug PRO
Consists of
LA-4572 CombiProbe 2 Hardware
LA-4553 Whisker TriCore DAP Streaming for CombiProbe
LA-1947 Automotive HALF-SIZE-CABLE 26-10
LA-1948 Automotive HALF-SIZE-CABLE 26-20
LA-1949 Automotive HALF-SIZE-CABLE 26-26
DAP streaming cable for CombiProbe
Supports
- DAP (DAP2, DAP3, DAPWide, DAP4): up to 160 MHz,
3.3 V or 5.0 V
- JTAG: 1.8-5.0 V, up to 60 MHz
- DXCPL
DAP streaming requires a DAP mode. For performance reasons,
we recommend DAPWide at 160 MHz.
26-pin Automotive Connector
CombiProbe Hardware
Only sold as part of a CombiProbe package
Whisker Cable MIPI60-Cv2 for CombiProbe
Requires one of the following extension cables:
LA-1228 Flex Ext. for SAM 60 pin QTH-QSH series 05.00
LA-1238 Flex Ext. for SAM 60 pin QTH-QSH series 12.00
CombiProbe 2 Hardware
Only sold as part of a CombiProbe package
Package for CombiProbe MIPI60-Cv2
requires Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, PowerTrace, Power Debug II
or Power Debug PRO
requires an A-license
Superseded by LA-4590 Package CombiProbe 2 MIPI60-Cv2
Package for CombiProbe MIPI60-Cv2
requires Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, PowerTrace, Power Debug II
or Power Debug PRO
requires an A-license
Superseded by LA-4591 Package CombiProbe 2 MIPI60-Cv2 Long
Package for CombiProbe DCI OOB
requires Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, PowerTrace, Power Debug II
or PowerDebug PRO
requires an A-license
Superseded by LA-4595 Package CombiProbe 2 Intel® DCI OOB
Package for CombiProbe 2 ARM
Debug cable and 512 MByte of trace memory
Supports Standard-JTAG, cJTAG and
Serial Wire Debug Port
Bandwidth of 400 MBit/s per trace channel
requires at least one of the following A-licenses:
LA-7742A (JTAG Debugger License for ARM9 Add.)
LA-7746A (JTAG Debugger License for ARM7 Add.)
LA-7765A (JTAG Debugger License for ARM11 Add.)
LA-7843A (JTAG Debugger License for CORTEX-A Add.)
LA-7844A (JTAG Debugger License for CORTEX-M Add.)
Trace support (up to 4-bit) included:
- MIPI System Trace
- ITM via Serial Wire Output/TPIU
- ETM Cortex-M continuous mode via TPIU
Supports the following trace licenses:
LA-7970X (Trace License for the ARM Architecture)
requires Power Debug Interface USB 3.0,
Power Debug II or Power Debug PRO
5V tolerant inputs; max. output level 3.3V
Consists of
LA-4572 CombiProbe 2 Hardware
LA-4513 Whisker MIPI20T-HS CombiProbe/uTrace Arm
LA-2109 Half-Size-Cable 20-20 short
LA-2108 Half-Size-Cable 20-10 short
LA-2730 ARM Converter MIPI-20T to ARM-20
LA-4505 Whisker Cable MIPI34 for CombiProbe
LA-1937 MIPI-Half-Size-Cable 34-10
LA-1938 MIPI-Half-Size-Cable 34-20
LA-1939 MIPI-Half-Size-Cable 34
LA-3771 ARM Converter MIPI-34 to ARM-20 or TI-14
requires Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, PowerTrace, Power Debug II
or PowerDebug PRO
Intel MIPI60 Converged connector
requires at least one
LA-4611 Whisker Cable MIPI60-Q for QuadProbe x86/x64
possible are up to four
LA-4611 Whisker Cable MIPI60-Q for QuadProbe x86/x64
requires the following A-license:
LA-3776A JTAG Debugger for Intel x86/x64
Whisker Cable MIPI60-Q for QuadProbe Intel x86/x64
5V tolerant inputs; max. output level 3.3V
Requires one of the following extension cables:
LA-1248 Flex Ext. for SAM 60 pin QTH-QSH series 08.00
LA-1249 Flex Ext. for SAM 60 pin QTH-QSH series 24.00
Input Probe
CMOS probe with 8 inputs
Input Probe with variable threshold level
8 inputs with variable threshold 0..5 V
Output Probe
CMOS probe with 8 outputs
10 Clips + Cable for CIN8, COUT8, STG, PowerProbe
64 universal i/o pins, pulse generator,
8 analog inputs, 4 analog outputs,
64 channel, 50 MHz pattern generator,
logic state tester, connection tester
Trigger probe for PODBUS and ICD,
allows complex triggering with 8 input signals,
data mask, clock and data triggering, glitch trigger,
puls width trigger 20 ns to 6 ms
fixed threshold level 1.4 V
trigger output to PODBUS, frequency counter or DSO
adapter for 16-bit DIL-EPROM,
connection to DIL42 for 16, 32 and 64 MBit EPROM
adapter for 16-bit EPROM,
connection to SO44 for 16 MBit EPROM
Adapter to ESI-CON universal connector,
supports 8 and 16 bit, 3,3 V and 5 V devices,
up to 64 MBit, high-speed download 500 KByte/sec.
2 short adapters for 8-Bit PLCC-EPROMs (4,5 mm),
connection to PLCC32
supports devices up to 16 MBit, 8 and 16 Bit,
40ns access time,
including adapter for DIL28/32 and DIL40
supports up to two ROM Monitor licenses
supports devices up to 16 MBit, 8 and 16 Bit,
40ns access time, 3.3V
including adapter for DIL28/32 and DIL40,
supports up to two ROM Monitor licenses
supports devices up to 64 MBit, 8 and 16 Bit,
40ns access time,
including adapter for DIL28/32 and DIL40,
supports up to two ROM Monitor licenses
2 adapters for 8-Bit PLCC-EPROMs (10,6 mm),
connection to PLCC32
adapter for 16-Bit PLCC-EPROM (10,6 mm),
connection to PLCC44
Converter from DIL40 to SO44 package (1.27mm x 16mm)
for 16-Bit Flash
support 68K family
includes software for Windows
support 80C166, C165, C167, PMB2705 GOLD, ST10,
includes HLL debugger, operation system,
includes software for Windows
support 80C196, 80C194, 80C198,
includes HLL debugger, operation system,
includes software for Windows
support Z80 family,
includes HLL debugger, operation system,
includes software for Windows
supports SH702x/703x, SH701x/704x, SH705x
includes HLL debugger, operation system,
includes software for Windows
supports H8/300H and H8S
includes HLL debugger, operation system,
includes software for Windows
supports 386/486
includes HLL debugger, operation system,
includes software for Windows
supports 186 family
includes HLL debugger, operation system,
includes software for Windows
supports 286 family
includes HLL debugger, operation system,
includes software for Windows
Adapter for NEXUS on MAC71xx, MAC72xx
with 38 pin mictor connector
includes software for Windows, Linux and MacOSX
requires LA-7690 PowerTrace Ethernet 512 MB
Parallel NEXUS Adapter with AutoFocus technology
for Qorivva MPC5xxx/SPC5xxx and PX series
includes debugger for eTPU and GTM
Concurrent debugging of multiple e200 cores on
multicore processors requires a
License for Multicore Debugging (LA-7960X)
(not necessary for lockstep mode)
Voltage range:
1..5 V
TRACE port:
2..16 MDO (data) lines
1..2 MSEO (control) lines
Data Bandwidth:
up to 200 MBit/s
76-pin mictor connector requires one of the
following converters
LA-7631 for Mictor 38 on target
LA-7632 for Glenair 51 on target
LA-7636 for SAMTEC 50 on target
LA-7637 for SAMTEC 20 on target
includes software for Windows, Linux and MacOSX
requires PowerTrace hardware
please contact Lauterbach if the serial number of
your PowerTrace is lower than E03010003982
Supports debug/trace for MPC55xx/56xx
applied to a NEXUS Autofocus Adapter
includes debugger for single core and eTPU
Concurrent debugging of both cores in
dual-core chip requires a
License for Multicore Debugging (LA-7960X)
(not necessary for lockstep mode)
Converter from Mictor76 to Mictor38 for:
LA-7630 (NEXUS Debugger/Trace for MPC5xxx AutoFocus)
LA-7635 (NEXUS Debugger/Trace for MAC71xx AutoFocus)
LA-7645 (NEXUS Debugger/Trace for AVR32 AutoFocus)
Adapter from Mictor76 to Glenair51 for:
LA-7630 (NEXUS Debugger/Trace for MPC5xxx AutoFocus)
Converter from Mictor76 to Mictor38 for:
LA-7630 (NEXUS Debugger/Trace for MPC5xxx AutoFocus)
LA-7635 (NEXUS Debugger/Trace for MAC71xx AutoFocus)
Converter from Mictor76 to Samtec50 for:
LA-7630 (NEXUS Debugger/Trace for MPC5xxx AutoFocus)
LA-7635 (NEXUS Debugger/Trace for MAC71xx AutoFocus)
Converter from Mictor76 to Samtec20 for:
LA-7630 (NEXUS Debugger/Trace for MPC5xxx AutoFocus)
LA-7635 (NEXUS Debugger/Trace for MAC71xx AutoFocus)
Converter from Mictor38 to Samtec50 for:
LA-7610 (NEXUS Debugger and Trace for MPC5xxx)
Converter from Mictor38 to Samtec20 for:
LA-7610 (NEXUS Debugger and Trace for MPC5xxx)
JTAG only converter from Mictor76, Mictor38,
Samtec50, Samtec20 or JTAG14 to Mictor38,
Samtec50, Samtec20 or JTAG14.
(Not all connectors can be mounted at
the same time. Please refer to the FAQ
Universal_JTAG-Adapter-LA-7640.pdf)
Connector types for top and bottom side must
be ordered explicitly!
Converter from Samtec50 to Mictor38 for:
LA-7610 (NEXUS Debugger and Trace for MPC5xxx)
LA-7630 (NEXUS Debug/Trace for MPC5xxx AutoFocus)
Adapter for NEXUS on AVR32
(up to 16 bit MDO, up to 2 bit MSEO)
up to 200 MBit/s
Port Voltage 1.0 V .. 5.0 V
NEXUS probe provides 76 pin mictor connector
requires LA-7631 for Mictor 38 on target
includes software for Windows, Linux and MacOSX
only with PowerTrace Ethernet 256MB/512MB
or PowerTrace PX
please contact Lauterbach if the serial number of
your PowerTrace is lower than E03010003982
Supports debug/trace for NEXUSAVR32
applied to a NEXUS Autofocus preprocessor
Converter from Mictor 38 to 2.54 mm Connector
Debug/Trace Adapter for M32R SDI-3
Adapter for Debug and Trace on M32R SDI-3
includes software for Windows, Linux and MacOSX
only with PowerTrace Ethernet 256MB/512MB
or PowerTrace PX
voltage range 2.6V to 3.3V
Adapter for Debug on M32R SDI-3
includes software for Windows, Linux and MacOSX
requires a Power Debug Module
debug cable with 10 pin connector
Adapter 10 pin 100 mil to 50 mil
for M32R
only for LA-7661 (Debug Adapter for M32R SDI-3)
PowerTrace Ethernet 512 MB
Universal Trace Port Controller,
1 Giga Byte Trace Memory
includes logic analyzer with
17 digital channels, 1024 KSamples
requires PowerDebug II Ethernet or PowerDebug PRO
Host requirements:
USB 2.0 or 100/1000 MBit Ethernet interface,
1.0 GigaByte RAM
Universal Trace Port Controller,
2 Giga Byte Trace Memory
includes logic analyzer with
17 digital channels, 1024 KSamples
requires PowerDebug II Ethernet or PowerDebug PRO
Host requirements:
USB 2.0 or 100/1000 MBit Ethernet interface,
1.0 GigaByte RAM
Universal Trace Port Controller,
4 Giga Byte Trace Memory
includes logic analyzer with
17 digital channels, 1024 KSamples
requires PowerDebug II Ethernet or PowerDebug PRO
Host requirements:
USB 2.0 or 100/1000 MBit Ethernet interface,
1.0 GigaByte RAM
Upgrade from PowerTrace II 1 GByte (LA-7692)
to PowerTrace II 2 GByte (LA-7693)
Upgrade has to be performed by Lauterbach
Upgrade from PowerTrace II 1 GByte (LA-7692)
to PowerTrace II 4 GByte (LA-7694)
Upgrade has to be performed by Lauterbach
Upgrade from PowerTrace II 2 GByte (LA-7693)
to PowerTrace II 4 GByte (LA-7694)
Upgrade has to be performed by Lauterbach
PowerDebug II Ethernet
Universal debug controller,
500 MHz PowerPC, High-Speed FPGA,
10/100 Mbit, 1 Gbit Ethernet and
USB 2.0 (Windows/Linux)
Superseded by LA-3505 PowerDebug PRO Ethernet
PowerDebug Module Ethernet
Universal BDM debug and JTAG controller,
200 MHz PowerPC, 64 MB DRAM, High-Speed FPGA
USB 2.0 (Win98/2000/XP/Linux) included
can be upgraded to PowerTrace by LA-7691 (512MByte)
Superseded by LA-3505 PowerDebug PRO Ethernet
supports MC68330..341, 68349, 68360,
includes software for Windows, Linux and MacOSX
requires Power Debug Module
BDM Debugger for 68HC16 (ICD)
supports MC68HC16 all derivatives
includes software for Windows, Linux and MacOSX
requires Power Debug Module
not supported by PowerDebug PRO Ethernet
BDM Debugger for MCS12 (ICD)
supports MCS12 controllers which have
no global addressing mode
LA-7736 is required for S12P128, S12G128, S12Hx, ..
includes software for Windows, Linux and MacOSX
requires PowerDebug Module
Superseded by LA-3748 BDM Debugger for MCS12Z (ICD)
supports (1.8V - 5.0V) MPC7410
includes software for Windows, Linux and MacOSX
requires PowerDebug Module
debug cable with 16 pin connector
supports MPC74XX
requires a valid software guaranty or a valid
software maintenance key
not suitable for debug cables older than 02/2004
(blue ribbon cable)
please add the serial number of the base debug
cable to your order
supports (1.8V - 5.0V) PPC603, MPC74x and MPC75x
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 16 pin connector
JTAG Debugger for PPC603/MPC74x/75x
requires a valid software guaranty or a valid
software maintenance key
please add the serial number of the base debug
cable to your order
supports PowerPC MPC505, MPC555, MPC56X
MPC801, MPC821, MPC85x, MPC86x, MPC87x and MPC88x
includes software for Windows, Linux and MacOSX
requires Power Debug Module
(Processor BDM input signals have to be 3.3V
tolerant)
supports (1.8V - 5.0V) PPC40x
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 16 pin connector
supports PPC40x
please add the serial number of the base debug
cable to your order
supports PPC40x
requires a valid software guaranty or a valid
software license key
please add the serial number of the base debug
cable to your order
supports (1.8V - 5.0V) MPC82xx, MPC83xx
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 16 pin connector
supports (1.8V - 5.0V) MPC82xx, MPC83xx
(whisker version of the debug cable)
requires a valid software guaranty or a valid
software maintenance key
please add the serial number of the base debug
cable to your order
supports MCS08
includes software for Windows, Linux and MacOSX
requires Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, Power Debug II
supports (1.8V - 5.0V) MGT5100, MPC512x, MPC5200
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 16 pin connector
supports MGT5100, MPC5200, MPC512x
requires a valid software guaranty or a valid
software maintenance key
please add the serial number of the base debug
cable to your order
supports DSP5630x
includes software for Windows, Linux and MacOSX
requires Power Debug Module
not supported by PowerDebug PRO
debug cable with 14 pin connector
supports DSP568xx and DSP5683xx
includes software for Windows, Linux and MacOSX
requires Power Debug Module
Not supported by PowerDebug PRO
debug cable with 14 pin connector
supports JANUS 2
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 20 pin connector
supports ARM9 (0.4 V - 5 V)
supports 5-pin standard JTAG, cJTAG and
Serial Wire Debug Port
includes software for Windows, Linux and MacOSX
requires Power Debug Module
cJTAG and SWD require
Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, PowerTrace, Power Debug II
or PowerDebug PRO
supports ARM9
please add the serial number of the base debug
cable to your order
supports ARM9
requires a valid software guarantee or a valid
software maintenance key
please add the serial number of the base debug
cable to your order
JTAG Debugger for ARM10 (ICD)
supports ARM10 (0.4 V - 5 V)
supports 5-pin standard JTAG, cJTAG and
Serial Wire Debug Port
includes software for Windows, Linux and MacOSX
requires Power Debug Module
cJTAG and SWD require
Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, PowerTrace, Power Debug II
or PowerDebug PRO
JTAG Debugger License for ARM10 Add.
supports ARM10
please add the serial number of the base debug
cable to your order
JTAG Debugger Extension for ARM10
supports ARM10
requires a valid software guarantee or a valid
software maintenance key
please add the serial number of the base debug
cable to your order
supports M-CORE derivatives
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 14 pin connector
supports ARM7 (0.4 V - 5 V)
supports 5-pin standard JTAG, cJTAG and
Serial Wire Debug Port
includes software for Windows, Linux and MacOSX
requires Power Debug Module
cJTAG and SWD require
Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, PowerTrace, Power Debug II
or PowerDebug PRO
supports ARM7
please add the serial number of the base debug
cable to your order
supports ARM7
requires a valid software guarantee or a valid
software maintenance key
please add the serial number of the base debug
cable to your order
Converter to connect an ARM Debug Cable V1 (ARM-14)
to ARM-20 or to connect a newer ARM Debug Cable
(ARM-20) to ARM-14 target connector
ARM-14 is an obsolete connector specification,
do not use for new designs
Converter to connect a Debug Cable to a TI-14
connector which is used on many targets with
processors from Texas Instruments
Debugger for 196EA (ICD)
supports 196EA
includes software for Windows, Linux and MacOSX
requires Power Debug Module
not supported by PowerDebug PRO Ethernet
supports (1.8V - 5.0V) PPC440
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 16 pin connector
requires LA-7986 if the target has a
Mictor38 connector
supports PPC440
please add the serial number of the base debug
cable to your order
supports PPC440
requires a valid software guaranty or a valid
software maintenance key
please add the serial number of the base debug
cable to your order
supports Qorivva MPC5xxx/SPC5xxx (e200 cores)
and Freescale PX SERIES processors
eTPU, GTM and SPT debugging included
includes software for Windows, Linux and MacOSX
requires Power Debug Module
Concurrent debugging of multiple e200 cores on
multicore processors requires a
License for Multicore Debugging (LA-7960X)
(not necessary for lockstep mode)
debug cable with 14 pin connector
Superseded by LA-2708 Debugger for MPC5xxx Automotive PRO
supports PowerPC MPC5xxx (e200 cores)
eTPU and GTM debugging included
supports E-GOLD, E-GOLD+, DOLCE, UTAH, M2, X-GOLD101
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 16 pin connector
supports TriCore, PCP and GTM
supports JTAG and DAP
includes software for Windows, Linux and MacOSX
requires Power Debug Module
supports 16-pin standard JTAG
10-pin DAP interface requires LA-3815
and debug cable with serial number higher
than C0809xxxxxxx
Concurrent debugging of multiple TriCore cores on
multicore processors requires a
License for Multicore Debugging (LA-7960X)
(not necessary for lockstep mode)
debugging HSM requires Cortex-M license
LA-7844A (JTAG Debugger License for CORTEX-M Add.)
Superseded by LA-2707 Debugger for TriCore Automotive PRO
supports TriCore, PCP and GTM
please add the serial number of the base debug
cable to your order
supports a lot of SH2, SH3 and SH4
derivatives from Renesas
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 14 pin connector
Targets with 36 pin Hirose connector
require the converter LA-7980
OCDS Debugger for XC2000/C166S V2 (ICD)
supports C166S V2, XC16x, XE166, XC2000, X-GOLD102
includes software for Windows, Linux and MacOSX
requires Power Debug Module
supports 16-pin standard JTAG
10-pin DAP interface requires LA-3815
and debug cable with serial number higher
than C0809xxxxxxx
OCDS Debugger for XC2000/C166S V2 Additional
supports C166S V2, XC16x, XE166, XC2000, X-GOLD102
please add the serial number of the base debug
cable or CombiProbe to your order
supports MIPS32 4Kp, 4Km, 4Kc derivatives
and LEXRA LX4280
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 14 pin connector
supports MIPS32 4Kp, 4Km, 4Kc derivatives
and LEXRA LX4280
please add the base serial number of your debug
cable to your order
supports MIPS64 5Kc, 20Kc derivatives
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 14 pin connector
supports MIPS64 5Kc, 20Kc derivatives
please add the base serial number of your debug
cable to your order
supports Intel XSCALE derivatives
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 20 pin connector
supports Intel XSCALE derivatives
requires a valid software guarantee or a valid
software maintenance key
please add the base serial number of your debug
cable to your order
supports ARM11 (0.4 V - 5 V)
supports 5-pin standard JTAG, cJTAG and
Serial Wire Debug Port
includes software for Windows, Linux and MacOSX
requires Power Debug Module
cJTAG and SWD require
Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, PowerTrace, Power Debug II
or PowerDebug PRO
supports ARM11
please add the serial number of the base debug
cable to your order
supports ARM11
requires a valid software guarantee or a valid
software maintenance key
please add the serial number of the base debug
cable to your order
supports H8S (H8S/2319, 2329, 2339, 2367, 2368,
2377 and 2378) from Renesas
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 14 pin connector
supports Teak, Teaklite and Teaklite-II with
JAM interface
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 20 pin connector
supports Teak, Teaklite and Teaklite-II with
JAM interface
please add the serial number of the base debug
cable to your order
supports Teak, Teaklite and Teaklite-II with
JAM interface
requires a valid software guarantee or a valid
software maintenance key
please add the serial number of the base debug
cable to your order
Converter for MIPS-EJTAG 14 pins to 12 pins
to support Micronas MDE processor
Converter from large NEXUS model AMP50
to small NEXUS model AMP50
to adapt to NEXUS on Spanish Oak (MPC565),
Silver Oak (MPC561) and Green Oak (MPC563)
supports S-GOLD, S-GOLDlite, E-GOLDlite, X-GOLD
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 20 pin connector
supports S-GOLD, S-GOLDlite, E-GOLDlite, X-GOLD
please add the serial number of the base debug
cable to your order
supports S-GOLD, S-GOLDlite, E-GOLDlite, X-GOLD
requires a valid software guarantee or a valid
software maintenance key
please add the serial number of the base debug
cable to your order
Adapter for NEXUS on Spanish Oak (MPC565),
Silver Oak (MPC561) and Green Oak (MPC563)
with 38 pin mictor connector
includes software for Windows, Linux and MacOSX
only with PowerTrace Ethernet 256MB/512MB
or PowerTrace PX
AMP40NS NEXUS connector requires LA-7793
AMP50 NEXUS connector requires LA-7794
GLENAIR51 NEXUS connector requires LA-7797
Converter from the 38 pin mictor connector on
Nexus Adapter for MPC56x family/Mictor38 (LA-7791)
to NEXUS/AMP40NS
Converter from the 38 pin mictor connector on
Nexus Adapter for MPC56x family/Mictor38 (LA-7791)
to NEXUS/AMP50
Converter from the 38 pin mictor connector on
Nexus Adapter for MPC56x family/Mictor38 (LA-7791)
to NEXUS 51 pin Glenair connector
Converter for MIPS-EJTAG 14 pins to 24 pins
to support IDT processors
IMPORTANT:
This adpater can also be used for 20 pin
target connections, but a separate wire for
VCC is required. Please ask your local
distributor.
supports a lot of SH2, SH3 and SH4
derivatives from Renesas (0.4 - 5V)
for ARM JTAG interface
ASEBRK pin in only supported in conjunction with
LA-7818 Converter JTAG 20 to H-UDI 14,
LA-7822 Converter JTAG 20 to Hirose 36
or LA-7823 Converter JTAG 20 to Mictor 38
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 20 pin connector
supports a lot of SH2, SH3 and SH4
derivatives from Renesas
please add the serial number of the base debug
cable to your order
Converter for JTAG 20 pins to
H-UDI 14 connector for SH2/3/4 processors
Converter for JTAG 14 pins to
JTAG 20 connector for SH2/3/4 processors
Converter for JTAG 20 pins to
Hirose 36 connector for SH2/3/4 processors
Converter for JTAG 20 pins to
Mictor 38 connector for SH2/3/4 processors
Serial termination for SH4 JTAG-14 to
avoid debug signal disturbance
JTAG Debugger for C5500 DSP (ICD)
supports TMS320C55x (1.8V - 3.6V)
includes software for Windows, Linux and MacOSX
requires Power Debug Module
Debug cable with 20 pin connector
Requires LA-7748 if 14 pin TI target adapter is
used
JTAG Debugger License for C5500 DSP Add.
supports TMS320C55x
please add the serial number of the base debug
cable to your order
JTAG Debugger Extension for TMSC5500 DSP
supports C55x
requires a valid software guarantee or a valid
software maintenance key
please add the serial number of the base debug
cable to your order
JTAG Debugger for TMS320C5400 DSP (ICD)
supports TMS320C54XX (1.8V - 3.6V)
includes software for Windows, Linux and MacOSX
requires Power Debug Module
Debug cable with 20 pin connector
Requires LA-7748 if 14-pin TI target adapter is
used
JTAG Debugger License for C5400 DSP Add.
supports TMS320C54XX
requires a valid software guarantee or a valid
software maintenance key
please add the serial number of the base debug
cable to your order
JTAG Debugger Extension for TMSC54X
supports C54x
requires a valid software guarantee or a valid
software maintenance key
please add the serial number of the base debug
cable to your order
supports ZSP400 Core (LSI)
includes software for Windows, Linux and MacOSX
requires Power Debug Module
supports ZSP400 Core (LSI)
please add the serial number of the base debug
cable to your order
supports Blackfin Core
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 14 pin connector
supports StarCore DSP
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 14 pin connector
requires LA-3724 (Adapter for StarCore Boards
with Ejector) if target has a JTAG connector
with ejector
supports NEC V850 with N-Wire
includes software for Windows, Linux and MacOSX
requires Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, Power Debug II or
PowerDebug PRO
debug cable with 20 pin connector
requires LA-7936 if KEL connector is used on
the target
requires LA-7937 if Mictor connector is used on
the target
supports MMDSP
includes software for Windows, Linux and MacOSX
requires Power Debug Module
supports MMDSP
Requires
LA-3722 ARM Converter ARM-20 to Mictor-38
if the target has a Mictor-38 debug connector
please add the base serial number of your debug
cable to your order
supports NIOS-II
includes software for Windows, Linux and MacOSX
requires Power Debug Module
supports NIOS-II
please add the base serial number of your debug
cable to your order
supports C6xxx (0.4 V - 5 V)
includes software for Windows, Linux and MacOSX
requires Power Debug Module
Debug cable with 20 pin connector
Requires LA-7748 if 14 pin TI target adapter is
used
supports C6xxx
please add the base serial number of your debug
cable to your order
supports NEC VR-Series with N-Wire
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 20 pin connector
requires LA-7936 if KEL connector is used on
the target
requires LA-7937 if Mictor connector is used on
the target
Supports ARMv7-A/R based Cortex-A and Cortex-R 32-bit cores
supports 5-pin standard JTAG, cJTAG and
Serial Wire Debug Port (0.4 V - 5 V)
includes software for Windows, Linux and MacOSX
requires Power Debug Module
cJTAG and SWD require
Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, PowerTrace, Power Debug II
or PowerDebug PRO
Supports ARMv7-A/R based Cortex-A and Cortex-R 32-bit cores
please add the base serial number of your debug
cable to your order
supports ARM Cortex-A and Cortex-R (ARMv7, 32-bit)
requires a valid software guarantee or a valid
software license key
please add the base serial number of your debug
cable to your order
Supports Arm Cortex-M cores
trace support ETM Cortex-M via ETB included
20 pin Arm connector
supports 5-pin standard JTAG, cJTAG and
Serial Wire Debug Port, (0.4 V - 5 V)
includes software for Windows, Linux and MacOSX
requires Power Debug Module
cJTAG and SWD require
Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, PowerTrace, Power Debug II
or PowerDebug PRO
Supports ARM Cortex-M cores
trace support ETM Cortex-M via ETB included
please add the base serial number of your debug
cable to your order
Supports ARM Cortex-M cores
trace support ETM Cortex-M via ETB included
requires a valid software guarantee or a valid
software maintenance key
please add the base serial number of your debug
cable to your order
supports StarCore DSP for ARM JTAG interface
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 20 pin connector
supports StarCore
please add the base serial number of your debug
cable to your order
supports C28xx (0.4 V-5.25 V)
includes software for Windows, Linux and MacOSX
requires Power Debug Module
Debug cable with 20 pin connector
Requires LA-7748 if 14 pin TI target adapter is
used
supports TMS320C28xx (0.4 V-5.25 V)
please add the base serial number of your debug
cable to your order
supports M8051EW core
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 14 pin connector
supports M8051EW core
please add the base serial number of your debug
cable to your order
supports M8051EW core
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 16 pin connector (HITEX compatible)
supports R8051XC core
includes software for Windows, Linux and MacOSX
requires Power Debug Module
debug cable with 20 pin connector
supports R8051XC core
requires a debug cable with serial number
C0808xxxxxxx or higher
please add the base serial number of your debug
cable to your order
Converter from AMP MODU SYSTEM50 to Mictor fo
Converter from the 80 pin AMP MODU SYSTEM50
connectors on
Preprocessor for C16x and XC16x family (LA-7880),
EGOLD+ family (LA-7893) or EGOLD family (LA-7881)
to 2 x 38 pin Mictor connectors
Preprocessor for MPC500/800 Family Data V2
Trace Preprocessor with data for
MPC505, MPC555, MPC56X, MPC821, MPC860
with soldered edge connection
connector cable and software
max bus frequency 66MHz
Requires PowerTrace Version 6 or higher
to support more than 40 MHz
voltage range 2.5V to 5.0V
Preprocessor for complete EGOLD family
Preprocessor for EGOLD, EGOLD+, EGOLD+V3 and
EGOLDlite,
adaption to ICECON2,
Up to 56 MHz,
extended trace features: 4 x 1MB Trigger RAM
plus trigger features,
only with PowerTrace Ethernet 256MB/512MB
or PowerTrace PX
requires LA-7858 if 80 pin AMP connector is
used on the target
voltage range 1.8V to 3.3V
Converter from 2 Mictor to AMP MODU SYSTEM50
Converter from the 2 x 38 pin mictor connectors on
Preprocessor for complete EGOLD family (LA-7857) to
80 pin AMP connector
+ 80pol. Cable
Preprocessor for MPC500/800 Family (center)
Program trace flow for :
MPC505, MPC555, MPC821, MPC860
with soldered center connection
connector cable and software
Preprocessor for MPC500/800 Family (edge)
Program trace flow for :
MPC505, MPC555, MPC801, MPC821, MPC860
with soldered edge connection
connector cable and software
Preprocessor TriCore OCDS-L2 5V Samtec 60
Program flow trace for TriCore OCDS Level2
to Samtec 60 connector, cable and software
130 MHz clock speed, 3.0 - 5.5 V
2 x RISC-Trace-Depth
converter LA-7927 required for AMP40 connection
Preprocessor for C166 family
Preprocessor for C161 .. C167
adaption to connector for evaluation boards
Does not support Egold+V3!
only with PowerTrace Ethernet 256MB/512MB
or PowerTrace PX
voltage range 3.0V to 5.5V
Preprocessor for EGOLD family
Preprocessor for EGOLD
adaption to ICE-Connect and LAEGOLD
Does not support Egold+V3!
requires LA-7851 if 2 x 38 pin mictor connectors
are used on the target
Preprocessor for MPC500/800 Family Data
Trace Preprocessor with data for
MPC505, MPC555, MPC56X, MPC821, MPC860
with soldered edge connection
connector cable and software
max bus frequency 40MHz
Preprocessor for MPC860 and MPC821 TCON
Trace Preprocessor for MPC821 and MPC860,
connection to TCON240
Preprocessor for MPC850 and MPC823-TCON
Trace Preprocessor for MPC823 and MPC850,
connection to TCON200
Preprocessor for MPC555 TCON
Trace Preprocessor for MPC555
connection to TCON240
max bus frequency 40 MHz,
clock ratio 1/1 only
Preprocessor for ARM-ETM 120
Preprocessor for ARM7 and ARM9 Embedded Trace
Macrocell (ETM), connector cable and software,
120 MHz clock speed, 4 x Trace-Depth
2.5 to 3.3V
supports normal mode and 4 bit DeMux mode
Preprocessor for EGOLD+ family
Preprocessor for EGOLD+
adaption to ICE-Connect and LAEGOLD+
Does not support Egold+V3 (7850) !
requires LA-7851 if 2 x 38 pin mictor connectors
are used on the target
Preprocessor for MIPS flex cable
Preprocessor for MIPS,
supports EJTAG 1.5.3,
EJTAG 2.6 derivatives or higher,
MDE (LEXRA) and IDT
connector cable and software,
180 MHz clock speed, 4 x RISC-Trace-Depth
LA-7901 is required if a Samtec24 is used for
IDT processors
LA-7903 is required if a Samtec52 is used
for Micronas MDE (Lexra LX4280) processor
Superseded by LA-3906 Preproc. for MIPS32 AUTOFOCUS 600 MIPI
Preprocessor for SHx and RX with AUD,
connector cable and software,
200 MHz clock speed, 256 (512) K trace depth
voltage range 3.0V to 3.6V
Converter for Preprocessor for MIPS
Mictor38 to Samtec 24
to support IDT processor
Target connectors:
FTSH-112-04-L-DV (SMD, small height)
FTSH-112-04-L-D (through-hole, small height)
FW-12-05-L-D-XXX-150
(SMD, "XXX" selectable height)
FW-12-02-L-D-XXX-150
(through-hole, "XXX" selectable height)
Converter for Preprocessor for MIPS
Mictor38 to Samtec52
to support Micronas MDEB (Lexra LX4280) processor
Target connector:
FTSH-126-04-L-DV (SMD, small height)
FTSH-126-04-L-D (through-hole, small height)
FW-26-05-L-D-XXX-150
(SMD, "XXX" selectable height)
FW-26-02-L-D-XXX-150
(through-hole, selectable height)
Preprocessor for MPC880 and MPC885 TCON
Trace Preprocessor for MPC880 and MPC885,
connection to TCON320,
80 MHz bus clock
Converter for Preprocessor for MIPS
Mictor38 to Samtec52
to support Micronas MDED (Lexra LX4280) processor
Target connector:
FTSH-126-04-L-DV (SMD, small height)
FTSH-126-04-L-D (through-hole, small height)
FW-26-05-L-D-XXX-150
(SMD, "XXX" selectable height)
FW-26-02-L-D-XXX-150
(through-hole, selectable height)
Converter for Preprocessor for MIPS64
Mictor38 to Samtec40
to support TOSHIBA RBTX49xx EVBs
Converter for TriCore Level2
from AMP 40 pin (preprocessor)
to SAMTEC 60 pin (target)
Converter from Mictor38-5V to Mictor38-3.3V for ARM-ETM
Trace clock frequency limited to 150MHz
Trace port size limited to 16bit
Power source (5V): target board (pin 12)
Preprocessor for ETM 2-MICTOR 2 flex cables
Preprocessor for ARM7/ARM9/ARM10/ARM11
Embedded Trace Macrocell (ETM),
connector cable and software,
120 MHz clock speed, 4 x Trace-Depth, 2.5V-3.3V
support all ETM modes, with 2 Mictor connectors
2 mictor flex cables included
support max. 32 bit trace port size
Converter for TriCore Level2
from SAMTEC 60 pin (preprocessor)
to AMP 40 pin (target)
Program flow trace for TriCore OCDS Level2
connector (Samtec60), cable and software
180 MHz clock speed, 1.8 - 3.3 V
4 x RISC-Trace-Depth
converter LA-7927 required for AMP40 connection
Program flow trace for PPC4xx
720 MHz clock speed, (180 MHz trace clock)
0.9-3.3V, connector cable and software
requires LA-7983 if the target has a
20 pin male connector
ICD State-Timing Analyzer, 64 Channels 100 MHz,
32 Channels 200 MHz, 16 Channel 400 MHz,
Transient Recording,
128 KFrames, 48 Bit Time-Stamp,
Trigger Filter, Trigger Delay, etc.
Requires PODBUS-Interface, No SOC-CON Support
ICD State-Timing Analyzer, 64 Channels 100 MHz,
32 Channels 200 MHz, 16 Channels 400 MHz,
Transient Recording, 256 KFrames, 48 Bit Time-Stamp,
Complex Trigger, 8 Trigger Events, 4 Trigger Levels,
3 Counters (45 bit),
Trigger Filter, Trigger Delay, etc.,
50 MHz Pattern Generator (9 bit),
Requires PODBUS-Interface, Option for SOC Trace
Converter EXCALIBUR (200 pin) to SOCCON (MICTOR)
Preprocessor for ST40 8 Bit data AUD,
connector cable and software,
100 MHz clock speed, 4 x trace depth
voltage range 3.0V to 3.6V
Converter KEL connector to debug cable
Converter from 20 pin male connector of
LA-7835 (N-Wire Debugger for V850)
LA-7842 (N-Wire Debugger for NEC VR-Series)
to Mictor38
Converter KEL to Mictor
Converter KEL connector to preprocessor
NBD Interface support for V850
allows real-time-memory access to target
memory
Placed between Power Debug Module and Debug Cable
16 Pin/100 mil connection to target
Requires: PowerDebugUSB 2, PowerDebugEthernet or
PowerTrace
ICD State-Timing Analyzer, 204 Channels,
200(400) MHz State, 500 MHz Timing,
Transient Recording, 8 MB sample memory,
512 KFrames, 48 Bit Time-Stamp,
Trigger Filter, Trigger Delay, etc.
Requires PODBUS-Interface
Requires a valid software maintenance of
the debug system it is connected to
Converter 16 Pin OCDS level 1 connector to
Samtec 60 Tricore trace connector on target
Preprocessor for VR-Flex
Preprocessor for VR with TRCU,
200 MHz clock speed, normal trace depth,
support 4 and 16 bit bus width
Mictor connector to target
requires LA-7938 if KEL connector is used on
the target
voltage range 1.8V to 5.5V
probe set (3 pieces) for 3G/DigRF protocol
for the PowerIntegrators
(not supported by PowerTraceII analyzer slot)
differential RX;
differential TX;
single ended SysClkEna and
single ended ANY (for free use)
Mictor Probe for PowerIntegrator,
34 Channels (32 Data, 2 Clock),
0..5 V Input, 4 pF, 50 kOhm
Standard Probe for PowerIntegrator,
17 Channels (16 Data, 1 Clock),
0..5 V Input, 4 pF, 50 KOhm
includes a 20 pin male-male adaptor
Samtec Probe for PowerIntegrator,
34 Channels (32 Data, 2 Clock),
0..5 V Input, 4 pF, 50 kOhm
Mictor Probe for PowerIntegrator,
17 Difference Channels (16 Data, 1 Clock),
0..5 V Input, 4 pF, 50 kOhm
applicable to PowerIntegrator and PowerTrace II
4 Channels 0..5 V 12 Bit Resolution,
3 Current Sense Channels,
Conversion Rate 625K Samples/Sec
applicable to PowerIntegrator, PowerTrace II, PowerTrace Serial
CombiProbe and uTrace
CombiProbe and uTrace require
Converter CombiProbe/uTrace to
PI-Analog Probe (LA-4508)
Mictor Probe for PowerIntegrator,
33 Channels (32 Data, 1 pair of
differential clock),
0..5 V Input, 4 pF, 50 kOhm
Adapter SODIMM SDRAM to MICTOR
Requires three Mictor Probes
Adapter SODIMM DDR to MICTOR
Requires two Mictor Probes
plus one Mictor Differential Clock Probe
Adapter SODIMM DDR to MICTOR
Requires two Mictor Probes
plus one Mictor Differential Clock Probe
Samtec Probe for PowerIntegrator,
33 Channels (32 Data, 1 pair of differential
clock),
0..5 V Input, 4 pF, 50 kOhm
Adaptor for ESI-CON. plugged between
target and Eprom-Simlator-Probe
Requires 2 Mictor Probes or
3 Standard Probes
License for Multicore Debugging
Allows the concurrent debugging of
2 or more identical cores
Please add the base serial number of your Debug
Cable respectively the serial number of the CombiProbe/uTrace
to your order
No "License for Multicore Debugging" is needed if the
Debug Cable or the CombiProbe already has 2 debug licenses
For recording of USB1x and USB2
Support for filtering, trigger and
display on PID protocol level
Converter TEKTRONIX footprint to MICTOR connector
for PowerIntegrator
Adapter SODIMM SDRAM to MICTOR (left-hand version)
Requires three Mictor Probes
Adapter SODIMM DDR to MICTOR (left-hand version)
Requires two Mictor Probes
plus one Mictor Differential Clock Probe
Adapter SODIMM DDR2 to MICTOR (left-hand version)
Requires two Mictor Probes
plus one Mictor Differential Clock Probe
Support for On-Chip and Off-Chip Trace
for QorIQ PowerPC
please add the serial number of the base debug
cable to your order
Support for On-Chip and Off-Chip Trace
for Qorivva MPC57XX and SPC57X/SPC58X
please add the serial number of the base debug
cable to your order
Support for Embedded Trace Buffer of
CoreSight TEAKLITE-III
please add the serial number of the base debug
cable to your order
Trace License for ARM (Debug Cable)
Supports On-chip Trace for ARM Cores
(ETB, ETF, ETR, TBR)
please add the base serial number of your debug
cable to your order
1.) Support for EJTAG onchip trace on MIPS32
please add the base serial number of your debug
cable to your order
2.) Supports 4-Bit IFlow program trace by using
LA-4504 CombiProbe MIPS32-Debugger and 4-Bit IFLOW
Support for JTAG onchip trace on SH2A
please add the base serial number of your debug
cable to your order
supports X-GOLD102 (PMB7890) and X-GOLD110 (PMB7900)
MCDS features of C166S-V2 family through JTAG
Supports 4-Bit program trace by using
LA-4506 CombiProbe C166V2-Debugger and 4-Bit Trace
Trace License for C5500 DSP
Support for Embedded Trace Buffer of C5500 DSP
please add the base serial number of your debug
cable to your order
Support for Embedded Trace Buffer of
CoreSight CEVA-X
please add the base serial number of your debug
cable to your order
Support for Embedded Trace Buffer of C6000
please add the base serial number of your debug
cable to your order
Converter for SH4 AUD Trace 36 pins of
Yamaichi to SH4 AUD 36 pins on Hirose
Converter for preprocessor for PPC4xx MICTOR 38
(LA-7929) to 20 pin male connector (target)
JTAG Converter to Mictor 38 for PPC4xx
Converter MICTOR 38 (on Target)
to 16 pin male connector for JTAG Debugger for PPC400
(LA-7723)
and to 20 pin male connector Converter
for Preprocessor for PPC405 family (LA-7897)
Converter for ST40 AUD Trace
Converts Yamaichi 36 pins to AUD ST40 14 pins
Converter MICTOR 38 on target to
16 pin male connector JTAG Debugger PPC4XX
and MICTOR 38 of
LA-7929 Preprocessor for PPC4xx family fast flex or
LA-3900 Preproc. for PPC4XX AUTOFOCUS II Flex
required if no separate JTAG connector is provided
on the target
Preprocessor for QorIQ PowerPC high speed trace port
(Aurora based)
Connector cable and software
up to 4 lanes,
up to 6.5 Gbit/s per lane
Requires PowerTrace II
converters for Samtec22 or Samtec46 have to be
ordered separately if required
voltage range 0.15V to 1.25V
Serial preprocessor for ARM-ETM with HSSTP
Connector cable and software
Supported maximum speed per lane:
4 lanes @ 5.00Gbps
3 lanes @ 6.25Gbps
2 lanes @ 6.25Gbps
1 lane @ 6.25Gbps
Support ETMv1.x, ETMv3.x, ETMv4,
all versions of CoreSight-ETM and
Marvell's SETM
Requires PowerTrace II
voltage range 0.15V to 1.2V
Preprocessor for ARM-ETM with AUTOFOCUS Flex
Preprocessor for ARM/Cortex
Embedded Trace Macrocell (ETM),
Program Trace Macrocell (PTM),
Connector cable and software,
350 MHz clock speed, 4 x Trace-Depth,
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Support all ETM modes, with 2 MICTOR connectors,
Supports 1.8 to 3.3V - else contact support
Requires PowerTrace/Ethernet Version 6 or higher
or PowerTrace II
Support max. 32 bit trace port size for ARM11
Superseded by LA-7992 Preproc. for ARM-ETM/AUTOFOCUS II 600 Flex
Parallel preprocessor for ARM/Cortex
Embedded Trace Macrocell (ETM),
Program Trace Macrocell (PTM)
Connector cable and software,
600 MBaud (300MHz clock speed, DDR)
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Support all ETM modes, with 2 MICTOR connectors,
Supports 1.2 to 3.3V - else contact support
Requires PowerTrace II, PowerTrace PX
or PowerTrace/Ethernet Version 6 or higher
Hide Allowed License/Programmable/Converter Options
Allowed licenses:
LA-3901A Trace License for MicroBlaze AUTOFOCUS II
LA-3902A Trace License for SH2A, SH4, SH4A in AF II
LA-3903A Trace License for C6000 in AUTOFOCUS II
LA-3904A Trace License for TEAKLITE-III AUTOFOCUS II
LA-3905A Trace License for RAM Trace Port AUTOFOCUS II
LA-3907A Trace Lic. for Intel® Processor Trace AFII
LA-3913A Trace License for ARC AUTOFOCUS II
LA-3917A Trace License for Nios II AUTOFOCUS II
LA-7995A Trace License for TMS320C5500 AUTOFOCUS II
LA-7996A Trace License for Ceva-X AUTOFOCUS II
LA-7999A Trace License for StarCore AUTOFOCUS II
Programmable to:
LA-3920A Trace License for STRED AUTOFOCUS II
Converter:
LA-3768 ETMv1 Conv. Mictor-38, 2x MIPI-34 to MIPI-60
LA-3769 Conv. Mictor-38, 2x MIPI-34 to MIPI-60
LA-3809 Converter Mictor-38/ARM20 to MIPI-20
LA-3810 U8500 Conv. 2x Mictor38, 3x MIPI34 to MIPI60
LA-3812 OMAP4 Conv. 2xMictor, ARM20, MIPI34 to MIPI60
LA-3813 OMAP3 Conv. Mictor-38, MIPI-34 to Mictor-38
LA-3814 ETMv3 Conv. Mictor-38, MIPI-34 to MIPI-60
LA-3816 Converter 2x Mictor-38 to MIPI-60
LA-3818 Conv. Prepro.AF II Mictor, ARM20 to MIPI60
LA-3863 Converter ARM-20 to ALTERA-10/RISCV-10
Support for ARM/Cortex
Embedded Trace Macrocell (ETM),
Program Trace Macrocell (PTM),
if applied to an AUTOFOCUS II preprocessor
please add the serial number of the preprocessor to
your order
AUTOFOCUS II Preprocessors with serial number
C0806xxxxxx and lower have to be send to Lauterbach
Germany for an hardware upgrade
Parallel preprocessor for ARM cores
Embedded Trace Macrocell (ETM),
Program Trace Macrocell (PTM)
Connector cable and software,
600 MBaud (300MHz clock speed, DDR)
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Support all ETM modes, with SAMTEC60 MIPI connector,
Supports 1.2 to 3.3V - else contact support
supports up to 4 trace sources (mix of TPIU and STM)
Requires PowerTrace
(PowerTrace Ethernet Version 6 or higher)
Preproc. for TMS320C5500 AUTOFOCUS II Flex
Preprocessor for Real-Time Trace of C5500
Connector cable and software,
500 MHz clock speed, 4 x Trace-Depth,
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Supports 1.2 to 3.3V - else contact support
Requires PowerTrace Version 6 or higher
Trace License for TMS320C5500 AUTOFOCUS II
Supports off-chip trace port for TMS320C55x if
applied to an AUTOFOCUS II preprocessor
please add the serial number of the preprocessor to
your order
AUTOFOCUS II Preprocessors with serial number
C0806xxxxxx and lower have to be send to Lauterbach
Germany for an hardware upgrade
Preprocessor for Real-Time Trace of Ceva-X
Connector cable and software,
500 MHz clock speed, 4 x Trace-Depth,
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Supports 1.2 to 3.3V - else contact support
Requires PowerTrace
(PowerTrace Ethernet Version 6 or higher)
Supports off-chip trace port for Ceva-X if
applied to an AUTOFOCUS II preprocessor
please add the serial number of the preprocessor to
your order
AUTOFOCUS II Preprocessors with serial number
C0806xxxxxx and lower have to be send to Lauterbach
Germany for an hardware upgrade
Preproc. for STARCORE AUTOFOCUS II Flex
Show Allowed License Options
