TRACE32 Debugger for AR2315, AR7242, AR9344

Universal debug controller with
USB 3.0 for Windows/Linux/MacOSX

can be used for all TRACE32 Debug Cable and
for the TRACE32 CombiProbe

requires TRACE32 software DVD 2013/02 or newer


Includes
LA-1952 Wall Mount Power Supply
LA-1942 USB-2 Cable
LA-1943 USB-3 Cable
LA-7411 Trigger Connector for PowerTools

Universal debug controller with 1 Gbit Ethernet and
USB 3.0 for Windows/Linux/MacOSX

can be used for all TRACE32 Debug Cable and
for the TRACE32 CombiProbe

requires TRACE32 software DVD 2015/02 or newer


Includes
LA-1955 Desktop Power Supply
LA-1942 USB-2 Cable
LA-1943 USB-3 Cable
LA-7411 Trigger Connector for PowerTools

supports MIPS32 4Kp, 4Km, 4Kc derivatives
and LEXRA LX4280

includes software for Windows, Linux and MacOSX

requires Power Debug Module

debug cable with 14 pin connector

1.) Support for EJTAG onchip trace on MIPS32
please add the base serial number of your debug
cable to your order

2.) Supports 4-Bit IFlow program trace by using
LA-4504 CombiProbe MIPS32-Debugger and 4-Bit IFLOW

Universal Trace Port Controller,
512 MegaByte Trace Memory
Streaming rate up to 50 MByte/s

requires PowerDebug II Ethernet or PowerDebug PRO

Universal Trace Port Controller,
4 Giga Byte Trace Memory

includes logic analyzer with
17 digital channels, 1024 KSamples

requires PowerDebug II Ethernet or PowerDebug PRO

Host requirements:
USB 2.0 or 100/1000 MBit Ethernet interface,
1.0 GigaByte RAM


Includes
LA-7945 Standard Probe for PowerIntegrator/PowerTrace

Preprocessor for Real-Time Trace of MIPS32

EJTAG 2.6 derivatives or higher

600 MBaud (300MHz clock speed, DDR)
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Supports 1.2 to 3.3V - otherwise contact support

Requires PowerTrace
(PowerTrace Ethernet Version 6 or higher)

voltage range 1.2V to 3.3V



Includes
LA-1228 Flex Ext. for SAM 60 pin QTH-QSH series 05.00
LA-3845 Conv. Samtec60 to MICTOR38 for MIPS

Converter for MIPS-EJTAG 14 pins to 12 pins
to support Micronas MDE processor

Converter for MIPS-EJTAG 14 pins to 24 pins
to support IDT processors

IMPORTANT:
This adpater can also be used for 20 pin
target connections, but a separate wire for
VCC is required. Please ask your local
distributor.

Converter for Preprocessor for MIPS
Mictor38 to Samtec52
to support Micronas MDEB (Lexra LX4280) processor

Target connector:
FTSH-126-04-L-DV (SMD, small height)
FTSH-126-04-L-D (through-hole, small height)

FW-26-05-L-D-XXX-150
(SMD, "XXX" selectable height)

FW-26-02-L-D-XXX-150
(through-hole, selectable height)

Converter to connect a MIPS Debug Cable to an ARM-20 connector
on the target

Converter for Preprocessor for MIPS
Mictor38 to Samtec52
to support Micronas MDED (Lexra LX4280) processor

Target connector:
FTSH-126-04-L-DV (SMD, small height)
FTSH-126-04-L-D (through-hole, small height)

FW-26-05-L-D-XXX-150
(SMD, "XXX" selectable height)

FW-26-02-L-D-XXX-150
(through-hole, selectable height)

Converter to connect a Debug Cable to 10/20/34 pin
connectors specified by MIPI.


Includes
LA-1937 MIPI-Half-Size-Cable 34-10
LA-1938 MIPI-Half-Size-Cable 34-20
LA-1939 MIPI-Half-Size-Cable 34