Product Catalogue
Find TRACE32 product
Converter from Mictor38 of the ETM trace port plus IDC20A to Mictor38 of RTP port of TI chips Former name: Conv. Mictor38/ETM+JTAG20 to Mictor38/RTP
Converter from Mictor76 to Mictor38 for: LA-7630 (NEXUS Debugger/Trace for MPC5xxx AutoFocus) LA-7635 (NEXUS Debugger/Trace for MAC71xx AutoFocus) LA-7645 (NEXUS Debugger/Trace for AVR32 AutoFocus)
Converter from Mictor76 to Mictor38 for: LA-7630 (NEXUS Debugger/Trace for MPC5xxx AutoFocus) LA-7635 (NEXUS Debugger/Trace for MAC71xx AutoFocus)
Converter to connect an ARM Preprocessor and a CombiProbe to a Mictor connector on the target. This converter is designed for the OMAP3503 board from Spectrum Digital. The upper ETM signals on the Mictor can alternatively be used for system trace (SDTI).
Converter to MICTOR 38 connector on target from 16 pin male connector JTAG Debugger PPC4XX and MICTOR 38 of LA-7929 Preprocessor for PPC4xx family fast flex or LA-3900 Preproc. for PPC4XX AUTOFOCUS II Flex. Required if no separate JTAG connector is provided on the target.
Converter from Mictor76 to Mictor38 for LA-3909 (Preprocessor for RH850/V850 Flex Cable)
Probe to record digital signals from a Mictor connector: 34 Channels (32 Data, 2 Clock), 0..5 V Input, 4 pF, 50 kOhm. The probe requires one of the following modules. PowerIntegrator (LA-7940), PowerIntegrator II (LA-3940/3941/3942).
Converter to connect the IDC20A Debug Cable to a Mictor connector on the target providing both debug and trace signals. This is needed if you want to connect the Debug Cable without a Preprocessor and if there is only a Mictor on the target. Former name: ARM Converter ARM-20 to Mictor-38
Probe to record digital signals from a Mictor connector with differential clock signal: 33 Channels (32 Data, 1 pair of differential clock), 0..5 V Input, 4 pF, 50 kOhm. The probe requires one of the following modules. PowerIntegrator (LA-7940), PowerIntegrator II (LA-3940/3941/3942).
Probe to record differential digital signals from a Mictor connector: 17 Difference Channels (16 Data, 1 Clock), 0..5 V Input, 4 pF, 50 kOhm. The probe requires one of the following modules. PowerIntegrator (LA-7940), PowerIntegrator II (LA-3940/3941/3942), PowerTrace II (LA-7692/7693/7694), PowerTrace Serial (LA-3120/3520/3555/3560).
Converter for RX from 14 pin JTAG to Mictor 38 pin on target (only JTAG)
Converter Mictor connector to GPIO header of XILINX ML403/ML501 for Preprocessor for MicroBlaze (LA-3803) Preprocessor for Beyond AUTOFOCUS II (LA-3908)
Converter TEKTRONIX footprint to MICTOR connector for PowerIntegrator
Converter from a MIPI20T to a MICTOR38 connector with ETM pin-out, designed to connect a MIPI20T-HS Whisker (from a CombiProbe or MicroTrace) to a target with MICTOR38 connector. Can be used for debugging with optional 4-bit trace if a MICTOR38 connector with 4-bit ETM pin-out is mounted on the target.
Converter for RX AUD Trace, JTAG14 and Yamaichi 36-pin to Mictor38
Converter to connect the ARM Debug Cable or the CombiProbe to a Mictor connector on the target. This is needed if you want to debug without a Preprocessor and if there is only a Mictor connector on the target. The trace signals of the CombiProbe are connected to the lowest four trace signals of the Mictor (ETMv3 pinout, continuous mode). But tracing is normally no use case due to the bandwidth limitations of the CombiProbe. Former name: ARM Conv. ARM-20/MIPI-34 to Mictor-38