TRACE32 Debugger for IMX25, IMX27, IMX27L

supports ARM9 (0.4 V - 5 V)

IDC20A debug cable supports 5-pin standard JTAG, cJTAG and
Serial Wire Debug Port, (0.4 V - 5 V)

includes software for Windows, Linux and MacOSX

requires Power Debug Module

cJTAG and SWD require
Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, PowerTrace, Power Debug II
or PowerDebug PRO

Universal debug controller with
USB 3.0 for Windows/Linux/MacOSX

can be used for all TRACE32 Debug Cable and
for the TRACE32 CombiProbe

requires TRACE32 software DVD 2013/02 or newer


Includes
LA-1952 Wall Mount Power Supply
LA-1942 USB-2 Cable
LA-1943 USB-3 Cable
LA-7411 Trigger Connector for PowerTools

Universal debug controller with 1 Gbit Ethernet and
USB 3.0 for Windows/Linux/MacOSX

can be used for all TRACE32 Debug Cable and
for the TRACE32 CombiProbe


Includes
LA-1955 Desktop Power Supply
LA-1942 USB-2 Cable
LA-1943 USB-3 Cable
LA-7411 Trigger Connector for PowerTools

Universal Trace Port Controller,
8 Giga Byte Trace Memory

requires PowerDebug II Ethernet or PowerDebug PRO
and TRACE32 software DVD 2021/02 or newer


Includes
LA-2500 Mixed-Signal Probe COB 2/MicroTrace/PT-III

Supports On-chip Trace for ARM Cores
(ETB, ETF, ETR, TBR)

please add the base serial number of your debug
cable to your order

supports ARM9

requires a valid software guarantee or a valid
software maintenance key

please add the serial number of the base debug
cable to your order

Universal Trace Port Controller,
512 MegaByte Trace Memory
Streaming rate up to 50 MByte/s

requires PowerDebug II Ethernet or PowerDebug PRO

Universal Trace Port Controller,
4 Giga Byte Trace Memory

includes logic analyzer with
17 digital channels, 1024 KSamples

requires PowerDebug II Ethernet or PowerDebug PRO

Host requirements:
USB 2.0 or 100/1000 MBit Ethernet interface,
1.0 GigaByte RAM


Includes
LA-7945 Standard Probe for PowerIntegrator/PowerTrace

Parallel preprocessor for ARM/Cortex
Embedded Trace Macrocell (ETM),
Program Trace Macrocell (PTM)

Connector cable and software,
Variable threshold level and termination voltage,
AUTOFOCUS self calibration technology,
Support all ETM modes, with 2 MICTOR connectors,

Voltage: 1.2 to 3.3V - else contact support
Traceport: 1-32bit
Bandwidth: 9.6 Gbps (300MHz clock speed, DDR)
Connector: 2x38 pin mictor connector

Requires PowerTrace II / III, PowerTrace PX
or PowerTrace/Ethernet Version 6 or higher



Includes
LA-1370 Mictor Flex Extension

TRACE32 Front-End connecting to
- third-party virtual target/simulators
- third-party target server such as GDB
- TRACE32 Back-End

supports ARM, Cortex and XScale

floating license via RLM (Reprise License Manager)

Please add the RLM HostID of the license server
to your order (please see our FAQ)

Floating license to use the TRACE32 Instruction Set
Simulator for automated tests via script language
PRACTICE or via the TRACE32 Remote API

supports ARM/Cortex

for Windows32, Windows64, Linux32, Linux64
and Solaris, other platforms on request

floating license via RLM (Reprise License Manager)

Please add the RLM HostID of the license server
to your order (please see our FAQ)

Converter to connect an ARM Debug Cable to a MIPS-14 connector
on the target

Converter to connect the ARM Debug Cable to a Mictor
connector on the target providing both debug and
trace signals. This is needed if you want to connect
the Debug Cable without a Preprocessor and if there
is only a Mictor on the target.

Converter to connect a Debug Cable to a TI-14
connector which is used on many targets with
processors from Texas Instruments

Converter to connect a Debug Cable to a TI-14 or
TI-20-Compact connector which is used on many
targets with processors from Texas Instruments.

Converter to connect a 20-pin debug cable to 10/20/34 pin
connectors specified by MIPI


Includes
LA-1937 MIPI-Half-Size-Cable 34-10
LA-1938 MIPI-Half-Size-Cable 34-20
LA-1939 MIPI-Half-Size-Cable 34

Converter to connect an ARM Debug Cable V1 (ARM-14)
to ARM-20 or to connect a newer ARM Debug Cable
(ARM-20) to ARM-14 target connector

ARM-14 is an obsolete connector specification,
do not use for new designs

Converter to connect two ARM Debug Cable to one
connector on the target.

Old method to handle multicore debugging by using
two debugger hardware modules.

Converter from ARM 20-pin connector to
Altera 10-pin (Byteblaster) connector or
RISC-V 10-pin

Target connector pitch can be
2.54mm or 1.27mm (half size).


Includes
LA-2113 Half-Size-Cable 10

Galvanic isolation
for ARM debug cable
for automotive debug cable

Components rated to IEC60950-1 (600 V working voltage)

requires
Power Debug Interface USB 2.0/USB 3.0,
Power Debug Ethernet, PowerTrace, Power Debug II
or PowerDebug PRO

Merges up to 4 JTAG interfaces to a daisy-chain

requires that all JTAG interfaces use the same VTREF

includes 4 JTAG Cable 20 Pin (LA-1968)


Includes
LA-1952 Wall Mount Power Supply
LA-1968 Blue JTAG Cable 20 Pin

Adapter 20 pin 100 mil to 50 mil with cable.
Purpose: Use 20-pin Debug Cable with smaller target
connector. In case of ARM Debug Cable better use
MIPI-10 or MIPI-20 for new designs.


Includes
LA-2111 Half-Size-Cable 20

Converter to connect Preprocessor AUTOFOCUS II Mictor38
to MIPI60 (QSH) connector

ARM/Cortex: Converter to connect Mictor38 TRACE A
and TRACE B (32-bit ETMv3) and an ARM Debug Cable
to a MIPI60 connector on the target

x86/x64: Converter to connect Mictor38 TRACE A to
to a MIPI60 connector on the target

Converter to connect an ARM Preprocessor with
MICTOR-38 and a ARM debug cable with JTAG20 to a
20 pin connector specified by MIPI and CoreSight

It allows to use the Preprocessor on the 4 bit wide
trace port of the MIPI-20 connector

It can be re-configured for MIPI-34



Includes
LA-1937 MIPI-Half-Size-Cable 34-10
LA-1938 MIPI-Half-Size-Cable 34-20
LA-1939 MIPI-Half-Size-Cable 34

Converter to connect an ARM Preprocessor to a
MIPI-60 on the target. Suitable for up to 16-bit
ETMv3. The converter is prepared to support various
other configurations because all clock and data
signals of the MIPI-60 are connected to the
Preprocessor.

110 mm flex extension for Mictor 38pin connector

ARM Converter to connect an ARM Preprocessor with
one Mictor-38 for 16-bit ETMv1 and two CombiProbes
for two 4-bit system trace ports to a MIPI-60
connector on the target.

Converter to connect Preprocessor AUTOFOCUS II Mictor38
and 2 MIPI34 CombiProbes to MIPI60 (QSH) connector

ARM/Cortex: Converter to connect Mictor38 TRACE A (16-bit ETMv3)
and two MIPI34 CombiProbes to MIPI60 (QSH) connector on the
target

x86/x64: Converter to connect Mictor38 TRACE A and a MIPI34
CombiProbes to MIPI60 (QSH) connector on the target

Converter to connect an ARM Preprocessor and a
CombiProbe to a Mictor connector on the target.
This converter is designed for the OMAP3503 board
from Spectrum Digital. The upper ETM signals on
the Mictor can alternatively be used for system
trace (SDTI).

Converter to connect an ARM Preprocessor (up to
24-bit PTM/ETMv3) and up to three CombiProbes
(3x STM/STP) to a MIPI-60 connector on the target.
This converter is designed for U8500/U5500
from ST Ericsson.

Converter to connect an ARM Preprocessor (up to
18-bit PTM) and one CombiProbe (STM; two connection
options) or a Debug Cable to a MIPI-60 connector on
the target. This converter is designed for
OMAP4xxx based boards from Texas Instruments.

ARM Converter to connect an ARM Preprocessor with
one Mictor-38 for 16-bit ETMv3 and one CombiProbe
for a 4-bit system trace port to a MIPI-60
connector on the target