Product Catalogue
Find TRACE32 product
Debug probe suitable for most SoCs. This TRACE32 Product is a license carrier. It requires a suitable, programmed TRACE32 A-license. Requires Power Debug Interface USB 2.0/USB 3.0, PowerDebug Ethernet, PowerTrace Ethernet, PowerDebug II, PowerDebug PRO, PowerDebug E40. or PowerDebug X50 Voltage range 0.4V to 5V
Converter from IDC20A to 12 pin PMOD connectors with the JTAG pinout from SiFive. The adapter exists in two variants: with male and female PMOD connector. This adapter has the male PMOD connector. PMOD is an open standard defined by Digilent for peripherals used with FPGAs or microcontrollers. The PMOD pinout of this adapter does ONLY work with targets that use the pinout that was defined by SiFive. So it is not a general/official RISC-V pinout. In case of FPGA boards, the pinout may depend on the used FPGA image.
Converter from IDC20A to 12 pin PMOD connectors with the JTAG pinout from SiFive. The adapter exists in two variants: with male and female PMOD connector. This adapter has the female PMOD connector. PMOD is an open standard defined by Digilent for peripherals used with FPGAs or microcontrollers. The PMOD pinout of this adapter does ONLY work with targets that use the pinout that was defined by SiFive. So it is not a general/official RISC-V pinout. In case of FPGA boards, the pinout may depend on the used FPGA image.
supports RISC-V MIPI10 / MIPI20 connector on the target required: LA-3770 ARM Converter ARM-20 to MIPI-10/20/34 ALTERA-10/RISCV-10 connector on the target required: LA-3863 Converter ARM-20 to ALTERA-10/RISCV-10 includes software for Windows, Linux and MacOSX requires Power Debug Module voltage range 1.8V to 3.6V
Supports RISC-V 32-bit cores MIPI10 / MIPI20 connector on the target requires: LA-3770 Converter IDC20A to MIPI-10/20/34 ALTERA-10/RISCV-10 connector on the target requires: LA-3863 Converter IDC20A to ALTERA-10/RISCV-10 Includes software for Windows, Linux and macOS. Requires TRACE32 software R.2020.09 or newer. Requires Power Debug Module
Supports RISC-V 64-bit cores Multicore debugging included MIPI10 / MIPI20 connector on the target requires: LA-3770 Converter IDC20A to MIPI-10/20/34. ALTERA-10/RISCV-10 connector on the target requires: LA-3863 Converter IDC20A to ALTERA-10/RISCV-10. Includes software for Windows, Linux and macOS. Requires TRACE32 software R.2020.09 or newer. Requires Power Debug Module.
supports NIOS-II includes software for Windows, Linux and macOS requires PowerDebug Module IDC20A debug cable voltage range 1.8V to 3.6V
Converter to connect an Arm Debug Cable V1 (ARM-14) to IDC20A or to connect a newer IDC20A Debug Cable to ARM-14 target connector ARM-14 is an obsolete connector specification, do not use for new designs Former name: ARM Converter ARM-20 to/from ARM-14
Supports Intel XSCALE derivatives. Includes license for trace decoding. Uses IDC20A debug cable, which supports 5-pin standard JTAG, cJTAG (IEEE 1149.7) and Serial Wire Debug (SWD), (0.4V - 5V) Includes software for Windows, Linux and macOS. Requires PowerDebug base module.
Supports Hexagon from Qualcomm Includes license for multicore debugging and trace decoding. Uses IDC20A debug cable, which supports 5-pin standard JTAG, cJTAG (IEEE 1149.7) and Serial Wire Debug (SWD), (0.4V - 5V) Includes software for Windows, Linux and macOS. Requires PowerDebug base module.
MIPI20T-HS Whisker for the use with CombiProbe and MicroTrace. Voltage range: 1.2V...5.0V. Maximum trace port width: 4 pins. Maximum trace bandwidth: 400 MBit/s per trace pin.
Supports ARC EM/HS/EV/VPX, ARC 600/700, ARCtangent-A4/A5 Uses IDC20A debug cable, which supports 5-pin standard JTAG, cJTAG (IEEE 1149.7) and Serial Wire Debug (SWD), (0.4V - 5V) Includes software for Windows, Linux and macOS. Requires PowerDebug base module.
Supports VSPA Uses IDC20A debug cable, which supports 5-pin standard JTAG, cJTAG (IEEE 1149.7) and Serial Wire Debug (SWD), (0.4V - 5V) Includes software for Windows, Linux and macOS. Requires PowerDebug base module. Not supported are the very old 1st Gen. PowerDebug modules LA-7702 (without USB) and LA-7704 (with USB 1.1).
Supports CEVA-X. Uses IDC20A debug cable, which supports 5-pin standard JTAG, cJTAG (IEEE 1149.7) and Serial Wire Debug (SWD), (0.4V - 5V) Includes software for Windows, Linux and macOS. Requires PowerDebug base module.
Converter from IDC20A connector to Altera 10-pin (Byteblaster) or RISC-V 10-pin Target connector pitch can be 2.54mm or 1.27mm (half size)
Supports Xtensa Cores from Tensilica via an ARM JTAG interface Core trace decoding for TRAX (Trace RAM within core logic) included IDC20A debug cable, which supports 5-pin standard JTAG, cJTAG (IEEE 1149.7) and serial Wire Debug (SWD), (0.4V - 5V) Includes software for Windows, Linux and macOS Requires PowerDebug module Requires LA-3763 if 14 pin JTAG (Xtensa) connector is used
Replacement part 50 mm Automotive Debug Cable 26 to 20 pin for LA-2707 (Debugger for TriCore Automotive PRO) LA-2708 (Debugger for MPC5xxx Automotive PRO) LA-2709 (Debugger for RH850/V850 Automotive PRO) LA-3203 (Debugger for TriCore AUTO26 (PACK)) LA-3205 (Debugger for RH850/V850 AUTO26 (PACK)) LA-3206 (Debugger for MPC5xxx AUTO26 (PACK)) LA-3736 (JTAG Debugger for MPC5xxx Automotive) LA-3737 (JTAG Debugger for TriCore Automotive)
Supports TMS320C54xx. Uses IDC20A debug cable, which supports 5-pin standard JTAG, cJTAG (IEEE 1149.7) and Serial Wire Debug (SWD), (0.4V - 5V) Includes software for Windows, Linux and macOS. Requires LA-7748 if 14-pin TI target adapter is used.
Supports C6xxx. Uses IDC20A debug cable, which supports 5-pin standard JTAG, cJTAG (IEEE 1149.7) and Serial Wire Debug (SWD), (0.4V - 5V) Includes software for Windows, Linux and macOS. Requires PowerDebug base module. Requires LA-7748 if 14 pin TI target adapter is used.