Target Adaption JTAG14/OnCE to AUTO26/20/10 for MPC5XXX/SPC5XXX


The embedded tools company




Order
Order
Information
Support
Technical Support
 
TOP

Target Adaption JTAG14/OnCE to AUTO26/20/10 for MPC5XXX/SPC5XXX


Products

Order No.Probe
LA-3876Conv. JTAG14 OnCE to AUTO26 


Target Connector Type

PinsSamtec Order NoConnector TypeSupported FeaturesSamtec ASP Nr.
10FTSH-105-01-L-DVno shroudbasic debug featureson request
10FTSH-105-01-L-DV-Kkeying shroudbasic debug featuresASP-168330-03
10FTSH-105-01-L-DV-EJejector shroudbasic debug featureson request
20FTSH-110-01-L-DVno shroudfull debug featureson request
20FTSH-110-01-L-DV-Kkeying shroudfull debug featuresASP-168330-02
20FTSH-110-01-L-DV-EJejector shroudfull debug featureson request
26FTSH-113-01-L-DVno shrouddebug port sharing (with e.g. calibration tools)on request
26FTSH-113-01-L-DV-Kkeying shrouddebug port sharing (with e.g. calibration tools)ASP-168330-01
26FTSH-113-01-L-DV-EJejector shrouddebug port sharing (with e.g. calibration tools)on request
NOTE: The listed Samtec ASP order numbers are for target connectors with pin 7 (key pin) removed, pick & place and tape & reel.
Refer to Lauterbach when ordering at Samtec.
SAMTEC catalog page

Target pinouts

26-pin connector (AUTO26)

Signal

Pin

 Pin

Signal

    
VTREF12TMS
GND34TCK
GND56TDO
KEY(GND)78TDI
GND(PRESENCE)910RESET-
GND1112RESETOUT-
GND1314WDTDIS
GND1516JCOMP
GND1718EVTI-
GND1920EVTO-
GND2122BREQ-
GND2324BGRNT-
GND2526EXTIO
    

20-pin connector (AUTO20)

Signal

Pin

 Pin

Signal

    
VTREF12TMS
GND34TCK
GND56TDO
KEY(GND)78TDI
GND(PRESENCE)910RESET-
GND1112RESETOUT-
GND1314WDTDIS
GND1516JCOMP
GND1718EVTI-
GND1920EVTO-
    

10-pin connector (AUTO10)

Signal

Pin

 Pin

Signal

    
VTREF12TMS
GND34TCK
GND56TDO
KEY(GND)78TDI
GND(PRESENCE)910RESET-
    

Signal considerations for MPC5XXX/SPC5XXX

  • Following signals are N/C on the adapter, but should be connected on the target for use with the AUTO26 debug cable LA-3736: RESETOUT, WDTDIS, EVTI, EVTO, BREQ, BGRNT, EXTIO
  • Optional signals (leave N/C when unused): RESETOUT, WDTDIS, JCOMP, EVTI, EVTO, BREQ, BGRNT, EXTIO
  • If the pins EVTI and EVTO are assigned to functions other than debugging (e.g. GPIO), do not connect these signals to the debug connector.
  • If JCOMP pin is not connected to the debug connector, the processor's JCOMP pin (if implemented) must be tied to VTREF.
  • In 1149.7 (cJTAG) mode, following signals change:
    • TMS becomes TMSc
    • TCK becomes TCKc
    • TDI/TDO become N/C (tristated)

Compatible Debug Cables

The following debug cables are compatible with this adapter:




Copyright © 2017 Lauterbach GmbH, Altlaufstr.40, D-85635 Höhenkirchen-Siegertsbrunn, Germany  Impressum
The information presented is intended to give overview information only.
Changes and technical enhancements or modifications can be made without notice. Report Errors
Last generated/modified: 10-May-2017