Search results for "caes"

Developer Tool Operational Verification and Validation Cases and Procedures (TOVVCP)

General documentation of the TRACE32 Tool Qualification Support-Kit. Includes general documentation and the following test suites: - Debug - Coverage Includes additionally test suite - TRACE32 TriCore Instruction Set Simulator which requires LA-8096L 1 User Floating Lic. ISS Test Suite TriCore - TRACE32 M68K Instruction Set Simulator which requires LA-8097L 1 User Floating Lic. ISS Test Suite 68K Each test suite contains a set of test cases, corresponding test case documentation and results. Downloadable after registration in TRACE32 TQSK Customer Portal For Windows, Linux, and macOS.

Converter to connect the CombiProbe to a SD or Micro SD card connector in case the signals alternatively provide debug functionality

Converter from IDC20A to 12 pin PMOD connectors with the JTAG pinout from SiFive. The adapter exists in two variants: with male and female PMOD connector. This adapter has the male PMOD connector. PMOD is an open standard defined by Digilent for peripherals used with FPGAs or microcontrollers. The PMOD pinout of this adapter does ONLY work with targets that use the pinout that was defined by SiFive. So it is not a general/official RISC-V pinout. In case of FPGA boards, the pinout may depend on the used FPGA image.

Converter to connect the ARM Debug Cable or the CombiProbe to a Mictor connector on the target. This is needed if you want to debug without a Preprocessor and if there is only a Mictor connector on the target. The trace signals of the CombiProbe are connected to the lowest four trace signals of the Mictor (ETMv3 pinout, continuous mode). But tracing is normally no use case due to the bandwidth limitations of the CombiProbe. Former name: ARM Conv. ARM-20/MIPI-34 to Mictor-38

Converter from IDC20A to 12 pin PMOD connectors with the JTAG pinout from SiFive. The adapter exists in two variants: with male and female PMOD connector. This adapter has the female PMOD connector. PMOD is an open standard defined by Digilent for peripherals used with FPGAs or microcontrollers. The PMOD pinout of this adapter does ONLY work with targets that use the pinout that was defined by SiFive. So it is not a general/official RISC-V pinout. In case of FPGA boards, the pinout may depend on the used FPGA image.

DAP Converter 26-pin Automotive Debug Cable/16-pin Standard Cable (TriCore) to CAN Physical Layer Usage with Power Debug Interface USB 2.0/USB 3.0, or Power Debug II requires: LA-2707 (Debugger for TriCore Automotive PRO) LA-3203 (Debugger for TriCore AUTO26 (PACK)) LA-3737 (JTAG Debugger for TriCore Automotive) LA-7756 (JTAG Debugger for TriCore Standard) Usage with PowerDebug PRO, PowerDebug E40 or PowerDebug X50 requires: LA-2707 Debugger for TriCore Automotive PRO LA-3203 Debugger for TriCore AUTO26 (PACK)

Intended for use with MIPI20T-HS Whisker for CombiProbe/MicroTrace. Can be used for debug and 4-bit trace if a MIPI-34 connector is present on the target. There is a pin header to optionally receive trace signals from elsewhere. Can be used for connection to AUTOFOCUS II MIPI or PowerTrace Serial.

Supports ARC EM/HS/EV/VPX, ARC 600/700, ARCtangent-A4/A5 Please add the base serial number of your existing debug cable to your order. LA-3750A in LA-3737 Debugger for TriCore Automotive can not be used to debug a stand-alone ARC chip LA-3750A can not be programmed on LA-7756 Debugger for TriCore Standard

Intended for use with MIPI20T-HS Whisker for CombiProbe/MicroTrace. Can be used for debug and 4-bit trace if a MIPI-60 connector is present on the target.