Target Adaptation for C6000 Trace


The embedded tools company



 

Adaptation for C6000 Trace


The adaptation applies for the following TRACE32 products:

Order No.Probe
LA-3330Trace for C6000 via AUTOFOCUS II (PACK) 
LA-3331Trace for C6000 via AUTOFOCUS II MIPI (PACK) 
LA-3903Preproc. for C6000 DSP AF II Mictor38 Flex out of production
LA-3916Preproc. for C6000 AUTOFOCUS II MIPI60 out of production


 

MIPI60


Target Connector Type

SAMTEC Part NumberDescription
QSH-030-01-L-D-AHigh Speed Ground Plane Socket

Link to SAMTEC

Target Connector Placement

The adaptation uses one 60 pin Samtec connector. We recommend to place the odd numbered pins at the PCB border side (flex cable won't be twisted).

Pinout Arm CoreSight TPIU


Signal

Pin

 Pin

Signal

    
VREF-DEBUG12TMS|TMSC|SWDIO
TCK|TCKC|SWCLK34TDO|-|SWO
TDI56RESET-
RTCK78TRST- PULLDOWN
TRST-910DBGRQ TRIGIN
DBGACK TRIGOUT1112VREF-TRACE
TRACECLK1314GND
GND1516GND
TRACECTL1718TRACEDATA[19]
TRACEDATA[0]1920TRACEDATA[20]
TRACEDATA[1]2122TRACEDATA[21]
TRACEDATA[2]2324TRACEDATA[22]
TRACEDATA[3]2526TRACEDATA[23]
TRACEDATA[4]2728TRACEDATA[24]
TRACEDATA[5]2930TRACEDATA[25]
TRACEDATA[6]3132TRACEDATA[26]
TRACEDATA[7]3334TRACEDATA[27]
TRACEDATA[8]3536TRACEDATA[28]
TRACEDATA[9]3738TRACEDATA[29]
TRACEDATA[10]3940TRACEDATA[30]
TRACEDATA[11]4142TRACEDATA[31]
TRACEDATA[12]4344GND
TRACEDATA[13]4546GND
TRACEDATA[14]4748GND
TRACEDATA[15]4950GND
TRACEDATA[16]5152GND
TRACEDATA[17]5354GND
TRACEDATA[18]5556GND
GND5758GND
GND5960GND
    
Connect metal plate to GND

If TRACECTL is not available ("continuous" mode) pin 17 shall be tied to GND.
 

Mictor38


 

Target Connector Type



Tyco Part NumberDescription
2-5767004-2Vertical, surface mount, board to board/cable connector, RoHS compliant.
767054-1Vertical, surface mount, board to board/cable connector.
767061-1Vertical, surface mount, board to board/cable connector.
5767044-1Right angle, straddle mount, board to board/cable connector, RoHS compliant.

Link to Tyco Electronics

Target Connector Placement


The adaptation uses one or two 38 pin Mictor connectors.
The second connector is only needed if the target trace port provides more than 16 trace data pins and for 8/16 bit demuxed mode.
A separation distance of 1350 mil is required if adaption without flex cable is intended.
We recommend to place the even numbered pins at the PCB border side (flex cable won't be twisted).

Pinout Arm CoreSight TPIU


Connector "TRACE A"
Signal

Pin

 Pin

Signal

    
N/C12N/C
N/C34N/C
GND56TRACECLK
DBGRQ78DBGACK
RESET-910EXTRIG
TDO|-|SWO1112VREF-TRACE
RTCK1314VREF-DEBUG
TCK|TCKC|SWCLK1516TRACEDATA[7]
TMS|TMSC|SWDIO1718TRACEDATA[6]
TDI1920TRACEDATA[5]
TRST-2122TRACEDATA[4]
TRACEDATA[15]2324TRACEDATA[3]
TRACEDATA[14]2526TRACEDATA[2]
TRACEDATA[13]2728TRACEDATA[1]
TRACEDATA[12]2930GND
TRACEDATA[11]3132GND
TRACEDATA[10]3334VCC
TRACEDATA[9]3536TRACECTL
TRACEDATA[8]3738TRACEDATA[0]
    
Connect Pin 39,40,41,42,43 to GND


VCC needs to have VREF-TRACE level.

Connector "TRACE B" (only needed if more than 16 data bit)
Signal

Pin

 Pin

Signal

    
N/C12N/C
N/C34N/C
GND56N/C
N/C78N/C
N/C910N/C
N/C1112N/C
N/C1314N/C
N/C1516TRACEDATA[23]
N/C1718TRACEDATA[22]
N/C1920TRACEDATA[21]
N/C2122TRACEDATA[20]
TRACEDATA[31]2324TRACEDATA[19]
TRACEDATA[30]2526TRACEDATA[18]
TRACEDATA[29]2728TRACEDATA[17]
TRACEDATA[28]2930GND
TRACEDATA[27]3132GND
TRACEDATA[26]3334VCC
TRACEDATA[25]3536GND
TRACEDATA[24]3738TRACEDATA[16]
    
Connect Pin 39,40,41,42,43 to GND


VCC needs to have VREF-TRACE level.

 

CTOOLS60


This connector can be found on many TI boards.



Lauterbach provides the following converters to the CTOOLS60 pinout.

Picture
Order No.
Probe
Conv. Mictor38/JTAG20 to 60 Pin CTOOLS
Conv. 20 Pin JTAG to 60 Pin CTOOLS
Conv. 20 Pin JTAG con. swap to 60 Pin CTOOLS
Conv. MIPI60/JTAG20 to 60 Pin CTOOLS




Copyright © 2024 Lauterbach GmbH, Altlaufstr.40, 85635 Höhenkirchen-Siegertsbrunn, Germany   Impressum     Privacy Policy
The information presented is intended to give overview information only.
Changes and technical enhancements or modifications can be made without notice. Report Errors
Last generated/modified: 07-Mar-2024