Target Adaptation for Converter Converter AUTO26 to IDC20A / IDC20A-ETK / TI-14
 Product
| Order No. | Probe |
|---|
| LA-2748 | Converter AUTO26 to IDC20A/IDC20A-ETK/TI-14 | |
Pinout IDC20A ( normal, all jumper in 1-2 position)
|
Signal
| Pin
| | Pin
| Signal
|
|---|
| | |  | | |
| VREF-DEBUG | 1 |  |  | 2 | VSUPPLY (not used) |
| TRST- | 3 | | | 4 | GND |
| TDI | 5 | | | 6 | GND |
| TMS|TMSC|SWDIO | 7 | | | 8 | GND |
| TCK|TCKC|SWCLK | 9 | | | 10 | GND |
| RTCK | 11 | | | 12 | GND |
| TDO | 13 | | | 14 | GND |
| RESET- | 15 | | | 16 | GND |
| DBGRQ | 17 | | | 18 | GND |
| DBGACK | 19 | | | 20 | GND |
| | |  | | |
| Target connector, top-view |
Recommended Target Connector
- This is a standard 20 pin double row (two rows of 10 pins) connector (pin to pin spacing: 2.54mm/0.100").
- If terminal strip without shroud is used, the spacing marked with "A" must be a minimum of 30.6mm/1.2".
- Examples with housing: Samtec HTST-110-01-L-D (through-hole); Samtec HTST-110-01-L-DV (surface mount).
- Examples without housing: Samtec TSW-110-23-L-D; Berg 67996-120H.
|
Pinout IDC20A-ETK ( ETK, all jumper in 2-3 position)
|
Signal
| Pin
| | Pin
| Signal
|
|---|
| | | | | |
| VREF-DEBUG | 1 | | | 2 | VSUPPLY (not used) |
| WDTDIS | 3 | | | 4 | GND |
| TDI | 5 | | | 6 | GND |
| TMS|TMSC|SWDIO | 7 | | | 8 | GND |
| TCK|TCKC|SWCLK | 9 | | | 10 | GND |
| RTCK | 11 | | | 12 | GND |
| TDO | 13 | | | 14 | GND |
| RESET- | 15 | | | 16 | GND |
| BREQ- | 17 | | | 18 | GND |
| BGRNT- | 19 | | | 20 | GND |
| | | | | |
| Target connector, top-view |
Recommended Target Connector
- This is a standard 20 pin double row (two rows of 10 pins) connector (pin to pin spacing: 2.54mm/0.100").
- If terminal strip without shroud is used, the spacing marked with "A" must be a minimum of 30.6mm/1.2".
- Examples with housing: Samtec HTST-110-01-L-D (through-hole); Samtec HTST-110-01-L-DV (surface mount).
- Examples without housing: Samtec TSW-110-23-L-D; Berg 67996-120H.
|
Pinout TI-14 ( TI-14, all jumper in 1-2 position)
|
Signal
| Pin
| | Pin
| Signal
|
|---|
| | | | | |
| TMS|TMSC|SWDIO | 1 | | | 2 | TRST- |
| TDI | 3 | | | 4 | GND |
| VREF-DEBUG | 5 | |  | 6 | GND (KEY) |
| TDO | 7 | | | 8 | GND |
| RTCK | 9 | | | 10 | GND |
| TCK|TCKC|SWCLK | 11 | | | 12 | GND |
| N/C | 13 | | | 14 | N/C |
| | | | | |
| Target connector, top-view |
Recommended Target Connector
- This is a standard 14 pin double row (two rows of 7 pins) connector (pin to pin spacing: 2.54mm/0.100").
- If terminal strip without shroud is used, the spacing marked with "A" must be a minimum of 23mm/0.9".
- Examples with housing: Samtec HTST-107-01-L-D (through-hole); Samtec HTST-107-01-L-DV (surface mount).
- Examples without housing: Samtec TSW-107-23-L-D
|
|
