FAQs for ICE-166
|
|
 PDF document ( 30KB / 8-Feb-2011 ) |
FAQs for ICE-166 |
|
|||
|
|
||||
| ||||
 |
||
Power-Down Mode |
||
 |
The emulation system goes to SYSDOWN if the processor enters power-down mode. | |
|
The dual-port access must be set to DENIED and the " SYS.Option TestCloc"′ to OFF. The dual-port cannot work if the processor clock is disabled. SYS.ACCESS DENIED SYS.OPTION TESTCLOCK OFF |
||
|
||
Update C167E2 to C167E3 |
||
|
Can I update the C167E2 module to bondout type C167E3? | |
|
The module can be update by changing the chip and adding some wires. |
||
|
||
C167 Bondout Errata Sheet (BONDOUT) |
||
|
Which are the bugs in the bondout chip C167E Step BA | |
|
The PDF document is on the INFINEON server at http://www.infineon.com/products/ICs/34/pdf/16errata/167e/ba10.pdfor on our server. 
Download ba10.pdf (31K)
|
||
|
||
Clock Errors on E2 Bondout (BONDOUT) |
||
|
The emulator reports 5 different mapper error messages after reset | |
|
Clock Generator Problem The chip internal clock oscillator on the E2 bondout has an undefined clock selector setting after reset. Therefore the clock system can fail after power-up. The only turnaround is to switch down the emulator and target system, and restart the booting sequence again. |
||
|
||
Mixed MUX/NOMUX Operation (BONDOUT) |
||
|
Which Setting must be done for Mixed-Operations | |
|
If mixed MUX/NOMUX CS programming is used, the emulator bustype must be set to MUX mode. |
||
|
||
Wrong Clock Frequency on E2 Bondout (BONDOUT) |
||
|
The CPU runs at 50% of the selected clock frequency | |
|
The E2 Step AB Bondout has an internal divider error. Instead dividing by 2 it divides by 4 on the 0.5 PLL setting. Turnaround: Use internal VCO and douple the frequency. |
||
|
||
C167 Bondout Errata Sheet (E1) |
||
|
Which are the bugs in the bondout chip C167E Step BA | |
|
The PDF document is on the INFINEON server at http://www.infineon.com/products/ICs/34/pdf/16errata/167e/ba10.pdfor on our server.
Download ba10.pdf (31K)
|
||
|
||
Clock Errors on E2 Bondout (E2) |
||
|
The emulator reports 5 different mapper error messages after reset | |
|
Clock Generator Problem The chip internal clock oscillator on the E2 bondout has an undefined clock selector setting after reset. Therefore the clock system can fail after power-up. The only turnaround is to switch down the emulator and target system, and restart the booting sequence again. |
||
|
||
Wrong Clock Frequency on E2 Bondout (E2) |
||
|
The CPU runs at 50% of the selected clock frequency | |
|
The E2 Step AB Bondout has an internal divider error. Instead dividing by 2 it divides by 4 on the 0.5 PLL setting. Turnaround: Use internal VCO and douple the frequency. |
||
|
Copyright © 2012 Lauterbach GmbH, Altlaufstr.40, D-85635 Höhenkirchen-Siegertsbrunn, Germany Impressum The information presented is intended to give overview information only. Changes and technical enhancements or modifications can be made without notice. Last generated/modified: 1-Feb-2012 |