|
Target Adaption for SOC Trace |
 Function
The SOC trace enables sampling signals on nodes inside ASICs or FPGAs by implementing a scanner module.
At minimum 13 lines are used for connection of the adapter.
|
|
Software |
- Direct Channel Selection out of 1024 Channels
- Time Correlation
- Trigger to or from Debugger
- Parallel Tracing of 8 to 32 External Channels (max. 400 MHz Sample Rate)
|
|
Connector Version A |
This connector is very small, it can be used on production boards and is scalable for 8, 16 or 32 trace channels.
Target Connector
The adaption uses 1 male connectors on the target.
Subsets
To reduce the space on the target board, some subsets of the 40-pin connector are defined:
| Connector | Pins | Function | Notes |
|---|
 |
16 |
SOCCON with 8 trace channels |
|
 |
24 |
SOCCON with 16 trace channels |
|
 |
40 |
SOCCON with 32 trace channels |
|
Connector Orientation
|
|
Connector Version B (MICTOR) |
This connector is more stable, compatible to standard logic analyzer probes, but need more space.
Target Connector
|
|
Signals |
Connector Version A (SAMTEC 0.8 mm, 8 Trace Channels)
|
Signal
| Pin
| | Pin
| Signal
|
|---|
| | |  | | |
| GND | 1 |  | 2 | LOAD |
| DATA | 3 | | 4 | CLKIN |
| CLKOUT | 5 | | 6 | SYNCH |
| T00 | 7 | | 8 | T01 |
| T02 | 9 | | 10 | T03 |
| T04 | 11 | | 12 | T05 |
| T06 | 13 | | 14 | T07 |
| GND | 15 | | 16 | VCC |
| | |  | | |
Connector Version A (SAMTEC 0.8 mm, 16 Trace Channels)
|
Signal
| Pin
| | Pin
| Signal
|
|---|
| | | | | |
| GND | 1 | | 2 | LOAD |
| DATA | 3 | | 4 | CLKIN |
| CLKOUT | 5 | | 6 | SYNCH |
| T00 | 7 | | 8 | T01 |
| T02 | 9 | | 10 | T03 |
| T04 | 11 | | 12 | T05 |
| T06 | 13 | | 14 | T07 |
| GND | 15 | | 16 | VCC |
| T08 | 17 | | 18 | T09 |
| T10 | 19 | | 20 | T11 |
| T12 | 21 | | 22 | T13 |
| T14 | 23 | | 24 | T15 |
| | | | | |
Connector Version A (SAMTEC 0.8 mm, 32 Trace Channels)
|
Signal
| Pin
| | Pin
| Signal
|
|---|
| | | | | |
| GND | 1 | | 2 | LOAD |
| DATA | 3 | | 4 | CLKIN |
| CLKOUT | 5 | | 6 | SYNCH |
| T00 | 7 | | 8 | T01 |
| T02 | 9 | | 10 | T03 |
| T04 | 11 | | 12 | T05 |
| T06 | 13 | | 14 | T07 |
| GND | 15 | | 16 | VCC |
| T08 | 17 | | 18 | T09 |
| T10 | 19 | | 20 | T11 |
| T12 | 21 | | 22 | T13 |
| T14 | 23 | | 24 | T15 |
| T16 | 25 | | 26 | T17 |
| T18 | 27 | | 28 | T19 |
| T20 | 29 | | 30 | T21 |
| T22 | 31 | | 32 | T23 |
| T24 | 33 | | 34 | T25 |
| T26 | 35 | | 36 | T27 |
| T28 | 37 | | 38 | T29 |
| T30 | 39 | | 40 | T31 |
| | | | | |
Connector Version B (MICTOR)
|
Signal
| Pin
| | Pin
| Signal
|
|---|
| | | | | |
| VCC | 1 |  | 2 | LOAD- |
| CLKIN | 3 | | 4 | DATA |
| CLKOUT | 5 | | 6 | SYNCH |
| T15 | 7 | | 8 | T31 |
| T14 | 9 | | 10 | T30 |
| T13 | 11 | | 12 | T29 |
| T12 | 13 | | 14 | T28 |
| T11 | 15 | | 16 | T27 |
| T10 | 17 | | 18 | T26 |
| T09 | 19 | | 20 | T25 |
| T08 | 21 | | 22 | T24 |
| T07 | 23 | | 24 | T23 |
| T06 | 25 | | 26 | T22 |
| T05 | 27 | | 28 | T21 |
| T04 | 29 | | 30 | T20 |
| T03 | 31 | | 32 | T19 |
| T02 | 33 | | 34 | T18 |
| T01 | 35 | | 36 | T17 |
| T00 | 37 | | 38 | T16 |
| | |  | | |
| Connect Pin 39,40,41,42 and 43 to GND |
Attention ! MICTOR Pinout changed to be compatible with logic analyzer connectors
|
FTE-120-xxxxx
Features
Products
Adapter for SOC Trace
